H.W1: An iron-constantan thermocouple, according to tables, gives an e.m.f. of 0 mV at 0 °C, 5.628 mV at 100 °C and 21.846 mV at 400°C. It is to be used to measure temperatures in the range 0 to 400°C. What will be the non-linearity error, as a percentage of the full-scale output, at 100°C if a linear relationship is assumed over the full range?

H.W1: An iron-constantan thermocouple, according to tables, gives an e.m.f. of 0 mV at 0 °C, 5.628 mV at 100 °C and 21.846 mV at 400°C. It is to be used to measure temperatures in the range 0 to 400°C. What will be the non-linearity error, as a percentage of the full-scale output, at 100°C if a linear relationship is assumed over the full range?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

H.W: The input of a certain regulator increases by 3.5 V. As a result, the output voltage increases by 0.42 V. The nominal output is 20 V. Determine the regulation in %/V.
Build an AC/DC dual power supply circuit that draws a 60Vp-p sinusoidal voltage, to provide a dc output voltage of +15 V. Full analysis of voltages and currents should be included. What modifications would you recommend to draw more current while maintaining same output voltage?
Q4: Design a buck-boost converter to provide an output voltage 12V from a source that varies 'between 10V-16V. Given the load resistor is 10 ohm. assuming the frequency is 50 KHz and the output voltage ripple is 1.5% Specity: a. The duty ratio. b. The value of inductor. c. The value of capacitor. Note: Determine the values of inductor and capacitor with D1 only.
i need the answer quickly
Please show me how to solve the following practice problems in step by step solution Than you so much!
The circuit is shown below, Vin is the sinusoidal waveform with magnitude 5V and frequency is 100 Hz, R = 1 k, C = 1 uE, the chip is supplied by + 12 V source. a) What is the waveform of Yout? b) Calculate the magnitude of Vo c) If Vin is triangle waveform, what is the output waveform? -Vout , if Vin is triangle waveform with magnitude of 5 V (peak-to-peak value is 10 V) and frequency is 10 kHz, calculate waveform of you and the magnitude of I/?
This is an Electronic subject. Please provide a step-by-step working solution. Thank you.
a2/a.Design Circint as the following pescripton: A- the positive Cyycle of the vout signal is 3.2 and Negate cycle is 4-3 (Note: we must used preetical Diodes and vin is tov) 1B- the positive cycleg of vout is 5-3 and Negative cycle is (5. 4) [note: consider tovavd we must used Cupaetor with praetical Drade) Vin اضف ملف
Example 2.24) In the two-layer uniformly varying field electrode system separated by the X=0 plane, the amplitude of the electric field vector in the first layer is 80kV/cm and the angle it makes with the perpendicular component is 〖20〗^0. Since the relative electric constants of the layers are 4 and 2, respectively, calculate the tangential component of the electric field in the second layer.
Op amp and diodes are ideal. Derive Vout and sketch the transfer curve of Vin vs Vout. Please show complete solution.
24. A step up chopper has load voltage of 600V and is sup- plied from a constant de source of 150V. If the OFF time of the chopper is 40 µs and desired output voltage is 300V find ON time of the chopper? (A) 5 µsec (C) 30 µsec (B) 10 μsec (D) 40 µsec