H.W1 : An 2.44 m span cantilever beam has a rectangular section and reinforcement as shown in Figure. The beam carries a dead load , including its own weight of 2 kN.m and a live load of 1.22 kN.m. Using fy = 414 MPa and f. = 27.58 MPa , check if the beam is safe to carry the above loads. 3 # 7 2.44 m- 200 mm 460 mm 396 mm

H.W1 : An 2.44 m span cantilever beam has a rectangular section and reinforcement as shown in Figure. The beam carries a dead load , including its own weight of 2 kN.m and a live load of 1.22 kN.m. Using fy = 414 MPa and f. = 27.58 MPa , check if the beam is safe to carry the above loads. 3 # 7 2.44 m- 200 mm 460 mm 396 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Value m = 1350
USE NSCP 2015
5. The beam-column has a height of 7.5m and is a member of a braced frame. It is subjected to an axial load of DL-65KN and LL= 1OOKN. It is pinned at both ends. A W12X35 section was used and was made up of A-36 steel with Fy-250MPA. Compute the interaction value for beam- column based on NSCP 2015 code provisions. Ngelect the weight of the section. A = 6645 mm2 Zx- 839x10^3 mm3 d- 317.50mm Sx- 747x10^3 mm3 tw= 7.62 Rx= 133.35 bf= 166.62 ly= 10x10^6 mm4 tf- 13.21 Sy= 122x10^3 mm3 Ix= 119x10^6 mm4 Ry3 39.12mm 3.5 Note: Use C=D1.00%--0.2
a beam b = 350mm h = 660mm is reinforced with 2- 28mm compression bars and 4- 36mm tension bar. concrete cover is 60mm from centroid of the bar, if The beam is subjected to a maximum service dead load of 230KN m. determine the maximum service live load the beam can carry. use fc = 21Mpa, fy = 345MPA Select the correct response: MII = 244.02KN-m MII = 390.43KN-m %3D MII = 666.43KN-m MII = 436.43KN-m
Find the value of internal force member and state if it is in Tension or Compression
The simple beam shown, 76.2-cm. long ( = a + L + d ), is made of AISI C1022 steel, as rolled, left a forged. At a =25.4 cm , F1 = 1360.5 kg. is a dead load. At d = 25.4 in , F2 = 1088.4 kg. is repeated, reversed load. For N = 1.5 , indefinite life, and h = 3b , determine b and h . (Ignore stress concentration).
From A to B it is 7.5ft, from A to G it is 24ft.
Need help asap pls.
AW 21 x 93 A36 steel is used for a cantilever beam with a span of 5.0m PROPERTIES OF W 14 x 132 A = 17 600 mm? , = 862 x10 mm d = 549 mm 4 = 38.7 x10 mm tw = 14.7 mm bị = 214 mm t, = 23.6 mm The beam is used to carry a distributed dead load of 60kN/m and a distributed live load of 75KN/m A. Determine the shear flow at neutral axis. B. Determine the allowable shear capacity of the section using ASD NSCP 2001 C. Determine the design shear capacity of the section using LRFD NSCP 2015
DO NOT ROUND OFF IN BETWEEN SOLUTIONS.