H.W.9: Select an economical rectangular beam size and bar using ACI strength method. The beam is a simply supported span of 12 m and it carries a live load of 20 kN/m and a dead load of 25 kN/m including self-weight of beam. Use f = 28 MPa, fy= = 400 MPa.

Q: Determine the centroidal coordinates ( x-bar and y-bar) of the composite lines shown in feet.

A: Solution  Given the shape of the triangle  The base of the traingle b = 3ft And height of the…

Q: own in millimeters. Note: DRAW OR ILLUSTRATE THE SUB-AREAS AND INDICATE THE CENTROID OF EACH…

A: To find the centroid-

Q: Define Thermoplastic-Polyolefin Roofing.

A: Answer Thermoplastic-Polyolefin Roofing. Thermoplastic-Polyolefin Roofing is the strong and durable…

Q: You just purchased a beautiful sheet of plywood with birch veneer. Describe the layers and how the…

A: Brief concept introduction- Plywood- Plywood is made up of thin layers of wood veneer called "plies"…

Q: Q4/Classify the Bricks According to the Shape?

A: Question is based on the building materials . In the question we have to classify the bricks on the…

Q: Differentiate between Post tensioning and pre-tensioning process.

A: Pre-stressing is the application of an initial load on the structure so as to enable the structure…

Q: Define the difference in application between open stirrups and closed stirrups in concrete beams?

A: Basically function of the stirrups is to  Resist shear stress developed in the beam  Hold the main…

Q: Define Post-Tensioned Concrete.

A: To define: Post-Tensioned Concrete.

Q: What are the advantages of sag?

A: Sag is the main content of the overhead lines.

Q: Fill in the blanks / identification: An L-shape section composed of two 10 mm by 30 rectangles. What…

A: Solution

Q: Based on preliminary estimates and the architect’s design, a team member has developed the…

A: The given figure is shown below:

Q: 2 ft I ft 2 ft 1 ft 3 t

A:

Q: What is the meaning of tablet lamination and capping? How are these related to compression force?

A: Tablet lamination and capping:

Q: Define The ultimate strength design method

A: The ultimate strength design method: There are three design methods: 1.Working stress…

Q: Manufacture of Precast Concrete Structural Elements.

A: What are precast elements? It consists of the individual elements like walls, floors and roofs, as…

Q: Compare and contrast "Ordinary Timber and Mass Timber".

A: Answer Introduction Timber is known as a renewable construction material.

Q: (4) 5 &#8 187 #3" fé= 4000 pai Grade 60 steel NWC. Mn=?

A:

Q: What's the advantage of Composite structures?

A:

Q: 6. Based on the following figure, explain how the steel decking is built.

A: question given related to the steel deckfig also given let's discuss the how steel decking is built

Q: What lumber grade has > 80% clear wood?

A: Brief concept introduction- Lumber grade- Lumber is a sawn and formed wood product made from…

Q: Submerge interior and exterior plywood samples in water. Continually apply pressure until…

A: Introduction Plywood for the interior: Interior plywood is a material used for inside construction.…

Q: How Dry-laid-nonwoven fabrics are manufactured?

A: Dry-laid Nonwoven Fabric Manufacturing Process:

Q: The cabinet door in the image is most likely made of ... O a. LDF O b. Massive timber O c. Plywood O…

A: MDF stands for Medium Density Fiberboard. It is a type of engineered wood product made by combining…

Q: I INTRODUCTION on green concrete

A: Introduction- Green Concrete is a groundbreaking concept in the history of the concrete industry,…

Q: Green Uses of Concrete

A: Answer:- Concrete and Green concrete:- Concrete is the most commonly used man made material on…

Q: Define Plain portland cement concrete .

A: Plain Portland cement is the most widespread form of cement used as an essential component in…

Q: Yト 2" ×小

A: Given data  Composite member Dimensions  To find Centroid

Q: d. Calculate the area moment of inertia (ly) for design A and design B. Make sure to use the…

A: Given two designs,  The MI about centroidal y axis and polar moment of inertia through the…

Q: Differentiate laminate structural composites and sandwich panel structural composite.

A: Laminate structural composites and sandwich panel structural composites are two types of composite…

Q: Hardwood advantages and disadvantages.

A: Hardwood is obtained from broadleaved tress. example : Mahogany, Oak, Teak  etc   Advantage of…

Q: What is the Gypsum Board ? please explain it in details and usage

A: Uses and Advantages:Gypsum is utilized to plaster to provide a smooth, crack-free surface. Gypsum…

Q: Write any differences between plain and reinforced concrete column

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Submerge samples of interior and exterior plywood in water. Apply pressure continuously until…

A: Yes, few plywood gives us very impressive results. But it always depends on the method used to…

Q: What are the exposed durability categories for plywood? Provide an example of how each may be…

A: Introduction: This inquiry discusses plywood's exposed durability classifications.

Q: List all required code of practice in designing reinforced concrete structural members based on :…

A: For the design of reinforced structural members, certain codal provisions are applied.

Q: Explain the porosity of the bricks

A: The porosity of bricks, permeability of brick, and absorption are very essential factors that can…

Q: What is secondary compression?

A: Secondary compression:- It is a continuation of the volume change that started during primary…

Q: Question 53 Modular ratio 'm' for M25 grade of concrete is

A: Given: M25 grade of concrete. Es=2×105Ec=5000fckfck=25

Q: Explain Randomly Oriented Fiber Composites.

A: In the development and production of advanced composite materials (ACM) and fiber-reinforced…

Q: Q#3: Design Rcc slab for an Isolated Living room resting on masonry walls with following data:…

A: Design RCC Slab for an isolated living room resting on masonry walls with following data: room size…

Q: 4.3 Refer to the following figures, name the concrete construction type, and identify column…

A: Type of slab

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.