H.W. 2: What is the total active force/unit width of wall and what is the location of the resultant for the system shown in Fig.? Use the Coulomb equations and take a smooth wall so S=0° 7.0 m 9-100 kPX ABANS - 32° <-165 EN³ SHV 7-19.25 Sol 1 Sall 1 30.3 kPa 14 107.5 EN 131 EN T 13.7 171 R=40.6LN IN

H.W. 2: What is the total active force/unit width of wall and what is the location of the resultant for the system shown in Fig.? Use the Coulomb equations and take a smooth wall so S=0° 7.0 m 9-100 kPX ABANS - 32° <-165 EN³ SHV 7-19.25 Sol 1 Sall 1 30.3 kPa 14 107.5 EN 131 EN T 13.7 171 R=40.6LN IN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Using the portal method determine the member forces in the frame shown.
Determine the tensile force in chain D in the given chain system below. fou 6000b 42° 36°
From the figure, solve for each of the force in members
y3D3 W = 15 kN/m 个个 L%3D24M Determine the tension (KN) at midspan.
Example 18.14. A mass is held by three springs as shoun in Fig. 18.22. Assume the ing friction on the floor is negligible, as are the inertial effects of the rollers. The spring anstants are ki = 6 N/mm, k2 = 4 N/mm, k3 =2 N/mm, g= 9810 mm/sec". Find p. %3D %3D %3D k2 k3 160 N www www (a) Series and Parallel k1 160 N (b) Parallel Fig. 18.22: For Example 18.14
Determine major and minor principal stress
Determine the bar forces CD, GD, andGH.
I need the answer as soon as possible
The internal shear force Vat a certain section of a steel beam is 94 kips. If the beam has the cross section shown (assume a = 2 in., b1 = 4.4 in., b2= 7 in., tw= t;= 1 in., d = 11.9 in.), determine: (a) the value of Q associated with point H, which is located 2 in. below the top surface of the flanged shape. (b) the maximum horizontal shear stress Tmax in the flanged shape. y a Н tw b2 Answers: (a) Q = i in.3. (b) Tmax i ksi.
For the section shown in Fig.1 if the applied moment =200 KN.m, n=12, b =841 mm, d=500 mm, As =1814 mm2, bw=250 mm, and hf =106mm. Find fc1 in terms of fc 0.24 fc 0.218 fc 0.223 fc 0.264 fc 0.18 fc 0.213 fc 0.308 fc 0.173 fc
For the cross-section shown in figure. Torque,T= 150 kNmm. q1, q2 and q3 are the shearflows in cell I, II and cell III respectively. Here thickness of different sections are:t12 = t25=t56= 0.03t23 = t34 = t45 =0.04t61 = 0.035curve 61, t =0.025G = 55000 MPaDraw the shear flows distribution diagram for the given section
Determine the support reaction at C using Conjugate Beam Method. Indicate the negative sign if the answer is downward.