Grandfather amount and type of stress quotient in the aluminum material as a result of the forces described the effect of the Shafat shown in the attached picture bronze Aluminum Iron A=1000 mm² A=750 mm² A-850 mm² 20 KN 10 KN 15 KN 5 KN

Grandfather amount and type of stress quotient in the aluminum material as a result of the forces described the effect of the Shafat shown in the attached picture bronze Aluminum Iron A=1000 mm² A=750 mm² A-850 mm² 20 KN 10 KN 15 KN 5 KN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

kindly solve this please, thank you
IN THE SYSTEM SHOWN AS BELOW, A FORCE OF 200 N AFFECTS ON THE PIPE SWITCH. CONSISTING AT POINTS A AND B ON THE PIPE ACCORDING THAT THE PIPE'S DIAMETER IS 25 mm; FIND MAXIMUM and MINIMUM SHIPMENT STRENGTHS AT POINT A.
Find the ox value for the plate as shown below, where b1=d2%=D16 mm, d1=70 mm,b2%=90mm. (ENTER ONLY THE VALUES IN THE BOXES BY REFERING THE UNITS GIVEN IN THE BRACKET) b1 b2 d2 d1
A steel [E = 200 GPa] rod with a circular cross section is 9-m long. Determine the minimum diameter D required if the rod must transmit a tensile force of 32 kN without stretching more than 5 mm. O 13.70 mm O 19.15 mm O 26.22 mm O 16.26 mm O 20.46 mm
Please give solution in Handwritten format with free body diagram.
i li. In. O MMecnaniCS / مطلوب Untitled Section F1 F2 a F3 B. d F4 F5 Consider the following values: - a - 25 m; b - 5 m; a - 25 m; d - 5 m; F1 = 6 KN; F2 = 7 kN; F3 = 8 KN; F4 = 9 kN; F5 = 10 KN; a = 60°, 0 = 45°, B== 30° 1] What is the resultant moment of the five forces acting on the rod about point A? a) - 15.8 kN.m b) 74 kN.m c) 88 kN.m d) 59 kN.m e) 241 kN.m 0- 47 kN.m 2] What is the resultant moment of the five forces acting on the rod about point B? a) 218.8 kN.m b) – 117.8 kN.m c) - 131.6 kN.m d) 98.9 kN.m e) 125.4 kN.m f) - 224.2 kN.m 3] What is the resultant moment of the five forces acting on the rod about point C? a) 186.7 kN.m b) - 143.6 kN.m c) 114.6 kN.m d) - 217.9 kN.m e) 224.1 KN.m ) - 135.3 KN.m 4] What is the resultant moment of the five forces acting on the rod about point D? a) 217.8 kN.m b) – 139.5 kN.m c) 111.9 kN.m d) 206.9 kN.m e) - 127.1 kN.m f) 99.1 kN.m Activate 5] What is the moment of the force F2 about point E? Go to Setting f) 321.3 kN.m a) 121.7 kN.m…
ı need solution
The cross-sectional area of the bar is 5 cm². L. Aluminum Steel Aluminum 80 kN 20 kN 30 kN +70 kN D 3 m - 4 m 5 m What is the stress in steel?
I need the answer quickly
4) A simply-supported beam has a shear diagram shown in Figure 2. a) Draw the moment diagram based on this shear diagram. b) Draw the load diagram based on this shear diagram. c) Locate the inflection poit (or the point where the moment diagram crosses the horizontal tine) from the left support, in meters.
Please show full steps and explain
Question 5: The following 0.8" diameter steel bar has three loads applied, as shown. Assuming that E= 30,000,000 psi, determine the following: Stress at points A, B, and C Total elongation of the bar. Hint: 8- PL AE オー 2000 Ibs 2-0" 4000 Ibs I-0 7000 Ibs