gnet D. All of these 4. ch of the statements is true when there is change in magnetic field in a closed loop of wire. A. There is no current induced in the wire C. Electromotive force is induced in the wire B. The induced current is free to move in any direction of the wire D. All of these 5. Which of the following is NOT a way a magnetic field can be varied to induce a current in a wire? A. Rotate the coil inside the magnetic field B. Move the coil in and out the magnetic field C. Change the strength of the magnetic field D. Move the coil out of the magnetic field 5. What are the two main applications for AC?

gnet D. All of these 4. ch of the statements is true when there is change in magnetic field in a closed loop of wire. A. There is no current induced in the wire C. Electromotive force is induced in the wire B. The induced current is free to move in any direction of the wire D. All of these 5. Which of the following is NOT a way a magnetic field can be varied to induce a current in a wire? A. Rotate the coil inside the magnetic field B. Move the coil in and out the magnetic field C. Change the strength of the magnetic field D. Move the coil out of the magnetic field 5. What are the two main applications for AC?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1.Consider the magnetic core below.All dimensions are shown on the figure. The core is made up of legs with 2 different cross-sectional areas.The depth of core is 10cm.The relative permeability of the core is 2000. The current in the magnetising coil is 1 A. The number of turns of the coil is 2000.Calculate: (i)the reluctances and draw the magnetic circuit (ii)the flux in the core (iii)Flux densities B and field intensities H in legs having different cross-sectional areas. (iv)Verify Ampere's Law. Depth: 10 cm I=1A 20cm 2000 Turns 65cm 15cm 15cm 50cm 15cm ndo un of
#28 The correct answer is already highlighted, explain in a very simple way why that is the correct answer. Briefly discuss its concept & provide an illustrative example.
How can the polarity of an electromagnet be determined if the direction of current flow is known? 2. Define the following terms: 3. flux density 4. Permeability 5. Reluctance 6. Saturation Unit 13 Magnetic Induction 7. Name three factors that determine the amount of induced voltage in a coil. 8. What is the effect on induced voltage of adding more turns of wire to a coil? 9. Into how many time constants is an exponential curve divided? 10. Each time constant of an exponential curve is equal to what percentage of the maximum amount of charge? 11. An inductor has an inductance of 0.025 H and a wire resistance of 3 . How long will it take the current to reach its full Ohm's law value? Unit 15 Alternating Current . 12 What is the most common type of AC waveform? 13 How many degrees are there in one complete sine wave? 14 At what angle does the voltage reach its maximum negative value on a sine wave? 15 A sine wave…
A circular ring of radius 50cm with relative permeability of magnetic material core is 1000 and flux generated is 2mWb and current through the coil is 2mA. The total number of turns in the coil is Select one: Oa. 123 Ob. None of these Oc.3185 Crd.5678
Calculate the voltage of the DC source and the stored field energy of the actuator illustrated infigure 1.1. The dimensions of the magnetic circuit proposed in shown figure 1.2. The core of the magnetic circuit is made of cast steel material whose B-H characteristics is illustrated in figure 1.3. The coil in figure 1.1 has 250 turns, and the coil resistance is 5 ohms. For a given length g=5mm, a Dc source is connected to the coil to produce a flux density of 1 Tesla in the air gap.
An iron circuit with a small 0.75 mm air gap is shown in Figure 1. A 6000 turn coil carries a current I = 18 mA which sets up a flux within the iron and across the air gap. The cross section of the iron is a consistent 0.8 cm?, and the mean length of the flux path is 0.15 m. a) Redraw the magnetic circuit using schematic symbols of an electric circuit with reluctance in each part of the circuit. b) State's Ohm's Law for magnetic circuit. c) By neglecting the effect of fringing, calculate the reluctance of the circuit. d) Find the flux within the core. N = 6000 Iron circuit (4, = 800 for iron). Figure 1
Explain the following. A. Magnetic Field Strength B. Boundary Conditions
1. What is the relationship between voltage and current when there is saturation in the magnetic circuit? 2. When there is no saturation in the magnetic circuit, what is the relationship between voltage and current? 3. Briefly explain what caused the saturation in the magnetic circuit. 4. What happens to alternating current, alternating current, and alternating magnetic flux in a magnetic circuit when frequency increases? 5. When a magnetic circuit is saturated, explain two solutions that can be used so that the magnetic circuit is no longer saturated.
The length of a magnetic circuit in a moving iron instrument is 300mm.The coil around the soft iron core has 360 turns and takes a current of 1.75A.The core is square in section with sides of 20mm.Take the relative permeability of soft iron as 1100. Determine the magnetomotive force in the core. Determine the field strength. Determine the flux density. Determine the total flux.
Figure 1 shows a ring formed with two different materials – cast steel and mild steel. Mild steel has a mean length of 400 mm and an area of 500 mm². Cast steel has a mean length of 300 mm and an area of 312.5 mm2. The magnetisation curve for mild steel and cast steel is shown in Figure 2. Find the total MMF required to cause a flux of 500 µWb in the magnetic circuit. Determine also the total circuit reluctance. 1.8 Cașt steel Cast-steel 1.6 Silicon iron 1.4 Mild steel 1.2 1.0 0.6 Mild stel Cast iron 0.6 Figure 1: Ring arrangement 0.4 0.2 3000 4000 Magnetic field strength, H(A/m) 1000 2000 5000 600ỘI 7000 Figure 2: Magnetization Curve MMF = AT Reluctance = x 10* ΑT/Wb Flux density, B(T)
The dimensions of the circuit and the number of windings are indicated on the figure. a) Draw the equivalent circuit. b) Find the equivalent reluctance value of the magnetic circuit. c) Find the value of the total magneto-motor force produced by the coils wound on the magnetic core. d) Find the values of total magnetic flux and arm magnetic flux flowing through the magnetic circuit. e) Find the self-inductance value of each winding and the common inductance value between the windings.
The magnetic field inside a solenoid is: Select one: a. All the above O b. Proportional to the applied current. c. None of the above O d. Proportional to the number of turns.