Given this two-port representation of an op amp with stage 1 being the diff pair, stage 2 being the middle gain, and stage 3 being the output circuit, calculate the overall voltage gain from Vsig to load RL. Rsig=120 Ohms, Rit-2k, Av1-30, Ro1-1k, Ri2= 5k, Av2=200, Ro2=1k, Ri3-200k, Av3=0.9, Ro3=140 Ohms and RL = 100 Ohms

Given this two-port representation of an op amp with stage 1 being the diff pair, stage 2 being the middle gain, and stage 3 being the output circuit, calculate the overall voltage gain from Vsig to load RL. Rsig=120 Ohms, Rit-2k, Av1-30, Ro1-1k, Ri2= 5k, Av2=200, Ro2=1k, Ri3-200k, Av3=0.9, Ro3=140 Ohms and RL = 100 Ohms

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the circuit shown: b) Find AVS at (re = 102)? c) At CE removed, repeat the step b? d) At no load (AV=-250), find AV at RL = IK Q? CE RS VS 0.5K пичним 0.7K 0.1K 20K 200 Vo www 80K 2.2K VCC 15V
Comparing the AC parameters of the CB and CE amplifiers, the main difference is that the CB amplifier has O a. Very low input resistance O b.Input and output signals that differ in phase by 180 degrees O c. Higer output resistance O d. Higher voltage gain
Find the VTP and UTP and sketch the voltage transfer characteristic of the Schmitt trigger circuit.What is the output voltage Vo given the input signal is a) 2V and b)-2V Note. The output voltage levels of the comparator are 10V and -10V
Q4) The parameters for BJT are given as B = 100 and Va = 0.7V R13 Ic 5ka Q1 Ib R14 V7 -15V 200ka V6 5V a) Determine l b) Determine l. c) Determine d) What is the mode of operation of the BJT
Please solve all steps and write your answers legibly.
14) Calculate the transconductance using the VGS values of -2V and –3V. For ID values of 2.5 mA and 0.625 mA.
Determine the proper values of load resistance RL and maximum Zener current Izm to maintain the output voltage of 30V with on the input source E that will vary between 40V and 60V, the input resistance Rs is equal to 5002. Rs RL Yo
Which are the two junctions of a transistor? a) Emitter-base and emitter-collector 10 b) Emitter-collector and base-collector c) Emitter-base and collector-emitter d) Emitter-base and base-collector (11 - 15) Select True or False
22
a) Draw the DC equivalent model and use it to find the four quiescent operating parameters. b) Draw the AC equivalent model and use it to find Zin, Zout, and Av. Assume ẞ = 100. c) Draw the output bias plot (Ic vs. Vce) with load line and label all values. Rs = 0.5 k ww HH CC www www Vcc = 10 V R₁ = 56 ΚΩ R₂ = 12.2 ΚΩ www www Rc = 2 k O VO RE=0.4 k
In which of the following configuration does a MOSFET works as an amplifier? Select one: O a. All of the mentioned O b. Common drain (CD) O c. Common Source (CS) O d. Common Gate (CG)
29