Given the set of information above, determine the following: A) Number of ideal stages and the correct feed plate location B) Amount of distillate and bottoms

Q: 2. Explain in short major engineering difficulties in water treatment process

A: This question is based on water treatment process and the engineering difficulties associated with…

Q: Derive the Kremser equation for a stripper with three equilibrium stages

A: Kremser equation for stripping section is to be derived.

Q: What is the material and energy balance of liquid liquid extraction process

A: Liquid-liquid extraction: Liquid-liquid extraction is a separation operation in which the solute…

Q: What is the formula for crushing efficiency, given specific surface area of a product, mass…

A:

Q: Cite some important  discussion analysis based on the graph and data which involves the concept of…

A: Distillation is a separation unit operation in which the light key components are separated from the…

Q: Discuss the following:1. The similarities and dissimilarities between wet scrubbing process and gas…

A: Wet gas scrubbers are devices that are used to remove a variety of pollutants from exhaust gas from…

Q: What are the three major components of the process design of a packed tower?

A: Packed towers are long vertical columns filled with large quantities of tower packings and tower…

Q: What factors affect the operation of a distillation column and how ?

A: Distillation separates components of liquids from one mixture. This component separation is possible…

Q: Determine the number of enriching section operating lines when a distillation process is constructed…

A: Introduction: The process where the separation is carried out using distillation has 3 parts 1.…

Q: A 2 mm diameter glass tube is inserted into an open glass of water (contact angle between the tube…

A: Diameter of glass tube =  2 mmContact angle,  = 0

Q: A B Rate of deformation, duldy Shear stress, 7

A: There are several properties defined for fluid such as density, specific gravity, viscosity, etc. In…

Q: How is compressed gas released?

A: The compressed gases are hazardous while handling as the are stored under containers in very high…

Q: What is the difference between the loading point and the flooding point in a packed column?

A: Loading Point and flooding points refer to the operating conditions of packed column.

Q: Write the mobile and stationary phases in gas chromatography. What is the physical state of the…

A: Chromatography is a physical technique that finds application in the separation, identification, and…

Q: Convert a viscosity of 20 (g)/(cm)(s) to the American Engineering units (Ibr)(hr)/(ft?)

A: Given viscosity is 20 g/cm s Viscosity unit of g/cm s have to convert into American Engineering unit…

Q: With an aid of a diagram, compare between FOUR (4) ideal gas flow patterns in a membrane separator

A: ideally there are four different flow patterns for membrane separation process:1)complete…

Q: In the laboratory experiment "Plate and Frame Filter Press" 1. How is concentration related to the…

A: Introduction  Rate of filtration depends on the area of the filter cloth, the viscosity of the…

Q: Determine the terminal settling velocity of a coal particle of size 400 micron in water at 20 oC by…

A: We need to find settling velocity of coal particle water and then we need to compare it with…

Q: 5. Physical properties of the formation crude oil includes volume coefficient and viscosity.

A: The physical properties of crude oil vary according to its composition, the relative abundance of…

Q: i. percentage recirculation of air ii. Heat Load

A:

Q: 2. How is phase diagram of water different from most other materials show with sketches. What is its…

A: In a phase diagram; there are certain important terms which should be explained first. Different…

Q: In the laboratory experiment "Plate and Frame Filter Press" 1. Discuss its significance, and…

A: Filtration is the process of separation in which solids from the fluid sepaarted by passing through…

Q: It is necessary to determine the process flow diagram for the plant in the design of the material…

A: A process flow diagram is a diagram that gives the idea about the process, that is to be…

Q: It refers to the vapor that is brought back to the column for better separation.   a Distillate…

A: In distillation we have key component as feed, distillate,residue,reflux and boilup.

Q: If I want do a certain application in the process engineering, what is the best type of pump that…

A: Classification of pump:

Q: 27.) An extra plane would be inserted inside the crystal in a/an a) Edge dislocation b) Screw…

A: In the crystal lattice structure there are different defects are present in the lattice structure.…

Q: Steel is an example of  __________.   A. interstitial alloy   B. ionic solid   C. molecular solid…

A: We can say steel is an example of an interstitial alloy, due to the very small carbon atoms fit into…

Q: Provide an equipment description of Slurry Settler in FCC with reference:

A: To provide an equipment description of Slurry Settler in FCC (Fluid Catalytic Cracking) Dear…

Q: What are the assumptions made for mass transfer in the packed column?

A: Packed column is a distillation column that has packings in some sort of arrangement or in disorder.…

Q: (b) The general characteristics of three oil wells selected for artificial lift as production method…

A: Table of 3 well are given.

Q: 2. Outline the steps in ceramic processing technology. 3. With the help of a diagram, contrast the…

A: A ceramic is any of the various hard, brittle, heat-resistant, and corrosion-resistant materials…

Q: what is the actual air required per hour.

A: Ultimate and proximate analysis of the coal sample is given. Flow rate of coal = 11762 kg/h % Excess…

Q: Suggest and discuss 1(ONE) example of hard materials that is suitable for improving abrasive wear…

A: Hard materials are particularly suited for challenging circumstances like ploughing, mining, rock…

Q: A core sample is saturated with water, Weight of saturated sample in air is 22.5 g. Water-saturated…

A: Bulk volume of the sample is volume of the water trapped between the pores of the sample. The weight…

Q: 2. In 3D printing, small liquid droplets are formed when a liquid jet breaks up in spray and fuel…

A: it is given that

Q: Please discuss "Drilling problems related to drilling fluid rheological property"

A: Drilling muds or fluid is sued as carrier of rocks produced during the oil and gas drilling…

Q: Plate filter press is commonly used in industry due to its high strength, long service life and good…

A: tbatch = 60 min = 1 hr tdischarge + tcleaning = 10 min tfilteration = tcleaning = 10 min…

Q: In extractive distillation, why is a large concentration of solvent required in the liquid phase?…

A: Extractive distillation - it is the distillation in the presence of miscible,  high boiling,…

Q: Compose a problem about Material balance with chemical reaction including 3 unit process with…

A: In the problem statement it is asked to assume a reacting system with three unit process with…

Q: A decanter to separate oil from water is needed. The oil flow is 8,500 lb/hr, and the water rate is…

A: Given:   A decanter to separate oil from water.   The mass flow rate of oil, moil = 8500 lb/h The…

Q: Creep analysis results were obtained for wheat flour dough by applying a constant stress of 50 Pa…

A: The creep analysis can be done by the Kelvin-Voigt model but for the foods like wheat flour dough…