Given the processor circuit below, what is the address of the RF's write port in binary if instruction add Sto, St1, st2 is executed? Machine instructions: 000000 01001 01010 01000 00000 100000 PC +4 rst Id dm rd wd 112 dm a rd r2d dm wd wd ir w20 16 wa CTRL 15 11 IM RF addt ADD DM 31 26 irs_0 25 21 add2 rla 20 16 f_wa_s twd_s f we frte r2a we re ir31 26 r5 0 rst we rte r2e SE ir15 0 f_r2e add2s dm we dm re wa

Given the processor circuit below, what is the address of the RF's write port in binary if instruction add Sto, St1, st2 is executed? Machine instructions: 000000 01001 01010 01000 00000 100000 PC +4 rst Id dm rd wd 112 dm a rd r2d dm wd wd ir w20 16 wa CTRL 15 11 IM RF addt ADD DM 31 26 irs_0 25 21 add2 rla 20 16 f_wa_s twd_s f we frte r2a we re ir31 26 r5 0 rst we rte r2e SE ir15 0 f_r2e add2s dm we dm re wa

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

The "Add immediate unsigned" MIPS instruction: addi Rt, Rs, Imm requires the immediate field to be extended from 16 bits to 32 bits. If the value of the immediate field is: 1111000011110000 what will be the sign extended value of this field from 16 bits to 32 bits? Choose the best answer. 01111111111111111111000011110000 O 11111111111111111111000011110000 O This is a trick question. You cannot sign extend a negative number O 00000000000000001111000011110000 10000000000000001111000011110000 This is a trick question. You cannot sign extend a positive number
varue 40A, and AR has the value 4E5. Sterting with the FETCH, describe what happens untar the next FETCH. Make sure to indicate any updated register values as they happen. Memory (in are 0123 for 000 to 002, then 1002, 1801, 7800, F400 for 40A through 40D. AC starts with value 0F24, PC has the
Homework: Show how a 32Kbyte ROM module can be connected on an 8088 system using 2764 EPROM chips, occupying the address range starting from the address E0000H. Use the following address decoding circuits: Nand decoding circuits A line decoder and a Nand gate PLD decoding circuit Comparators only Line decoder and a comparator 1 Solution: A19 A18 A17 A16 A15 A14 A13 A12 A1... A. Memory Map Size of 2764 EPROM chips: Number of chips needed: Number of address lines: 66 2345
Given the binary format of an instruction as follows0000 0011 0000 1000 1000 1000 0110 0011a. What assembly instruction does this correspond to?b. If the PC = 0X0040 00F4, what is the target address?c. How many instructions forwards or backwards is that?d. How many bytes is that in decimal?
Change this MIPS code to RISC-V Assembly using store-load and 2 memory locations. Please add comments. Allow running in RARS.
If short JMP instruction reside in memory location 02001 what is the ?address of next instruction 02002 O 02003 O 02001 O none of them O
Given the instruction: LD RO, X005 If the instruction is stored in memory at x3000, how will data be moved? Data at address x3005 will be loaded into RO Data in RO will be stored into memory at x3006 Data at address x3006 will be loaded into RO Data in RO will be stored into memory at x0005
Differentiate between the Sequential and Nested techniques for dealing with many interruptions that are created at the same time.
Write a program in PLP assembly that repeatedly reads the value of the switches (address: 0xf0100000) and displays a pattern on the LED array based on what switches. Each time the switch value is read, the pattern should be displayed (regardless of whether the switch value has changed or not since the last time it was read). The table below indicates the pattern that should be displayed for each possible switch setting. - please use"sw" "li", labels, loops, "beq" and "lw" to create the code. The code is for assambly language and it will be compiled and run on PLPTool version 5.2. I have created the following code it is not completed it. I seem to be stuck here. Please complete it, following the task instructions. # main source file .org 0x10000000 _start: # Initialization li $t0,0xf0100000 # Load address of switches li $t1,0xf0200000 # Load address of LEDs li $t5,1 # Load value of switch 0 address of LEDs li $t6,2 # Load value of switch 1 address of LEDs…
translate c code in risc-v 32 bit assembly instructions, then convert to machine code(hex) variables a, b, and c are stored in a1, a2, and a3, respectively. Use register a1 for all intermediate values. C code: a=b+c-64; here's what i have so far addi a1,a2,a3 addi a1,a3,-64
I asked the question before and the answer I got does not makes sense. My question is why did not we considered the Adder, Shift, ANd, Control when calculation delay time.? Again, it is in Risc-V.
Q1 Write a sequence of instruction to poll switch at 17 of 74F244 that is connected to port 0. ALE CLK G₁ Ag-A 74F138 Input/Output B Address decoder C G 74F244 Input 1 Port Buffer Vcc 8086 MPU MNMX AD-AD MIO DT/R DEN RD AD AD 74F373 (2) Address latch OE 74F245 Data Transceiver (bi-directional) DIR G AIL Az A Au G G₂A D-D