Given the inputs A,B,C and D please make a truth table for the outputs at points F,G and H (а) U8 A: U14 F U9 OR U15 B OR NAND U11 NAND U13 U12 NOT U10 AND C- NOT I.

Q: From the given Ammeter diagram, the span is -- A. J0407 A a. -1 O b. 4 О с. 3 o d. -1 to 3

A: Given, Ammeter diagram

Q: it should be E1/R1 +I1 in the numerator and everything else is basically the same but the + I1 is…

A:

Q: Design a digitall to compute the 9 5 compliment of a binary coded decimalcode word. logic circvit…

A: Binary coded decimal digits exist only from 0 to 9 in decimal. The 9's complement of these digits is…

Q: The correct voltage waveform of the following clipper

A: Draw the The voltage waveform of the following clipper ?

Q: Q3/find the total charge for the distribution charge equal 5 nc/m³ on 2 <x< 3, 3< y< 4, 4 <z< 5 Q4/…

A: In this question we will find total charge with given volume charge density.... Note:- as per…

Q: What is the I total

A: For the given series RLC circuit the value of total current needs to be calculated and the same can…

Q: Calculate the values current circuits, of f each branch for the super posilion 330-n 5602 Ri es 3 k…

A: In the given superposition circuit we have to find the branch curent

Q: What is the voltage across R1?

A: To find the voltage across resistance R1 in the circuit

Q: 7). Defarmne the nde equations.. P4 VA VB Vc I3 Ii 善Pu Is

A: In this question we will write node equations..

Q: A JFET is a + driven device

A: in JFET the output characteristics are determined by the electric field and the electric field…

Q: subtract 58 from 29 using 15's and 16's compliment

A:

Q: Design a counter that count from zero to nine

A:

Q: Q4/ The minimum Carry save Adder using to add 15 numbers are

A: The explanation is as follows.

Q: A three phase overhead transmission line,\300 km are arranged as shown in the previous pundle…

A:

Q: Is this an L circuit matching box?

A: An image is given as shown-

Q: A. Explain your back ground about the diode and Zener diode.

A: A diode is a semiconductor device that essentially acts as a unidirectional switch for current. It's…

Q: Hydroelectric genarators are

A: The explanation is as follows.

Q: perform the following operations in Octal (with and without complement): 152 – 77

A:

Q: Draw the state diagram of 1011 without overlapping.

A: The state diagram is visual representation of the sequence. It shows the internal states and…

Q: What is the conductance of the z = 5+j90 ?

A: Impedance is sum of the resistance and reactance. Resistance = 5 ohm Reactance = 90 ohm

Q: Circutt A Circult B 3. Circuit is wired in parallel, and circuit is wired in series.

A:

Q: 3 Find 640 Ix In um in the circuit shown :- 1:2 Ix₂ CS Scanned with CamScanner -so HH zVk 211 821

A: Given A circuit which contains transformer and dependant voltage source.

Q: the question is for tan(2-j3)

A: Brief description: For the given complex trigonometric function we need to derive its rectangular,…

Q: Determine what these four voltmeters (A, B, C, D) will register when connected to this circuit in…

A: Voltage across a short circuit is zero  So voltmeter connected across short circuit will register…

Q: b/ We obtained the following values from alternating voltage measurements by means of a d-organza…

A:

Q: What is Kelvin's double bridge?

A: It is a measuring device used to estimate unknown electrical resistors below 1 ohm. It is designed…

Q: lab Questions 1. How can the duty ratio (D) effects on the converter output (Vo)

A: Let us consider a general buck converter .

Q: 23. What is the waveform across D1? halfwave fullwave sinewave DC line 24. What is the waveform…

A: 23. whenever diode conducts then voltage across the diode is constant i.e, for silicon diode it is…

Q: Full adders are made by combining half adders true or false

A: Half adder: Half adder is a combinational  circuit which used to add two bits and produced the sum…

Q: For each of the following Circuit Diagram. (use two flip Elop Aand B Dnive the state Epua tion Dnive…

A: Given the sequential circuit. We need to derive the state equation in the first part. In the second…

Q: 1. WHAT TYPE OF CIRCUIT SHOWN ? 2. WHAT WILL BE THE FREQUENCY AT C IF THE CLOCK IS 320 HZ? 3.…

A: Answer:- 1) Since external clock pulse has been applied to the only one flip flop(right most flip…

Q: MOVITG to dilouler queston will save uns Tesponse. Quèstion 13 The number 45A may be base 10 may be…

A: We are know that when Base 16 Numbers are 0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,F So  From the Question The…

Q: 30 60 20 a 30 ww ww

A: This question is based on basic resistance properties of added in parallel and series . The solution…

Q: A Ceel of Emf avat and naglibee resistence is Connected in Jenes with 3,5,2 ohm resintora. Draw the…

A: given a cell of 2 volt and three registers of 3 ohm 5 ohm and 2 Ohm are connected in series

Q: Question 8 Phosphorus(P15) atoms are trivalent. O True False

A: Atomic number of phosphorus is 15

Q: Calculate C and L:

A: According to the question, we need to calculate the equivalent capacitance and inductance of the…

Q: What is metastability? For the Circuit, what is the Maximum Frequency of Operation? FF1 FF2 thold…

A: Flip flop is a latch with additional control input (clock or enable ). A flip flop is used to store…

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.