Given the forces Q = 480 N, P = 700 N and tension in cable BD TBD = 1,300 N, determine the reactions at C.

Q: Q4: For Fig.4, the required force to be exerted at A by the lever ABC is 4.2lb. If the spring exerts…

A: Given dataForce exerted at point A FA = 4.2lbSpring force Fs = 15lbTo determine the value of angle…

Q: Determine the vertical reaction at point O. ( 625 N 750 N 200 N 1m 300 N 1.25 m 1.25 m

A:

Q: loh: proced ● Determine reactions at A and C A 2 m MB 1m -C Rc

A:

Q: 6) Find the horizontal and vertical components of the reactions at points A and D. 2m D -1.5 m B 1.5…

A: Given

Q: Q2: Determine the reactions at the Smooth contact points A,B and C 250 N 30% 04 m 30° 0.2 m 0.15 m B…

A:

Q: 10 N 80 N Ra (400, 200 200, 300 20 N 50 N (200, 500) $400, S00) R, R1 3. A table 600 mm by 600 mm is…

A: Draw a diagram for the problem showing the reactions on each leg. Here, R1, R2, and R3 are the…

Q: A has a fixed support and B has a sliding support. Determine the reaction forces occurring in A and…

A: P1 = 40 kN P2 = 20 kN L = 6 m

Q: For the frame shown in Figure, determine the reaction at A, B, and D. 80 kN/m 20 kN/m B 4 m 6 m

A:

Q: 2kN/m D 4kN 4m 4m C 4m 4m 3m

A:

Q: 450 N PA +1.5m 2.5m 2.0 m B D 1.5 m 3.0 m + 100 N 1.5 m TRE 85 N

A:

Q: The frame shown is supported by three cables and a ball-and-socket joint at A. For P = 0, determine…

A: To find: Tension in each cable The reaction at point A.   Free body diagram of the frame:

Q: Determine the reactions at the point .(A) and (B) 5KN 2.4M 1-2 m 1.2m 1.2m

A: For the given simply supported beam  To determine  reaction at point A and B

Q: Question 3 (Type B): The 50 N force F is parallel to the y axis. Determine the components of the…

A: The force F is

Q: Determine the reactions at the supports. 350 N/m 150 N/m 80 N/m 3.5 m 4.5 m

A: Given: To determine the support reactions. The load will be divided as uniformly distributed load…

Q: The moment reaction at point C equals to 600 N 900 Ν || 1m 1 m 2 m |A 800N-m 1.5 m C

A:

Q: Solve for all reactions at A and B

A: The free-body diagram of the given truss system can be drawn as below, Here, RB is the normal…

Q: Find the forces of each members and the reaction of in the truss.

A:

Q: For the lightweight truss shown 9 kN 12 kN 9 kN H G F! 30° E 10 m 10 m 10 m 10 m ( all 30°, 60°, 90°…

A: there are two types of supports  1st Hinge support  2nd Rollar support

Q: Find the support reactions at the ball and socket 3. support A and the tension, T1 and T2.

A: Given data: F=133 kNCoordinates of A=0, 0, 0Coordinates of B=0, 0, 9Coordinates of C=4, 3,…

Q: The guy wires AB and AC are attached to the top of the transmission tower. The tension in cable AB…

A:

Q: Show the complete solution: Two cables tied together as shown in figure , Knowing that Q = 60 lbs…

A: Consider the free body diagram of the point C.

Q: Example2:Thickness of plate (6mm) .Thermal conductivity (20W/m.°C) ,heat generation (3x10'W/m')…

A: Given data, t = Thickness of the plate = 6 mm = 0.006 m k = Thermal conductivity of the plate = 20…

Q: The moment reaction at B is

A:

Q: : Determine the reaction at A,E,B 6° B 12 640b

A:

Q: The trepezoidal jack is in equilibrium Find the relationship between the forces P and G at the…

A: It is asked to find the relationship between G and P, by using the method of virtual work

Q: W W a

A: given:

Q: F E 30° 30° A D В C 6 ft -6 ft- 6 ft 300 lb 300 lb

A:

Q: Q4/ For equilibrium condition, determine M, and the reaction at O. 150 mm M 150 mm 60° 30° 320 N 160…

A:

Q: The pulley is frictionless and members ACE and BCD are weightless, Find the reactions at points A,…

A:

Q: C 2 m 3 m 4 m 52 kN 30° D B.

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.