Given the following Resistances and Inductors in Series and Voltage Source: R1 = 1,664 ohms R2 = 1,999 ohms L1 = 2 Henry L2 = 2 Henry Vs = 3 Volts Frequency 92 Hz What is the Total Impedance (Amplitude) in ohms?

Q: Figure 2 shows three "LC" circuits, two of them with capacitors of capacitance "C" and the three…

A:

Q: The voltmeters in the figure measure RMS voltages. If V, = 23 V and V, = 14.5V what is V3? R V V3 23…

A:

Q: Problem 5 Find the equivalent inductance Leg for the network shown below. 72 mH oooo Leq 49 mH elle…

A:

Q: a)For the inductive element of Figure 1 , the current in phasor form is B) the voltage in phasor…

A: The solution can be achieved as follows.

Q: j202 Select one: O a. None of these O b. Is 100 <-90° mA O c. Is = 5.0<.90° A 90° me ell

A:

Q: what is average power delivered to R4

A: Fig: Given circuit

Q: 7. In a pure inductive circuit, the phase angle between the voltage waveform and current waveform…

A: In an inductor voltage leads the current  And in capacitor current leads voltage. The pahsor diagram…

Q: Determine the DC currents (1s. Ic and le) and dc junction voltages (VBE, VCE and Vca) In-Blank 1 mA,…

A: Given,  VBB = 3 VRB = 5 kΩRC = 232 ΩVcc = 18 VβDC = 65

Q: What are the things common in direct current and alternating current. And also its Difference

A: The explanation is as follows.

Q: QUESTION 3 An inductor, a capacitor, and a resistor are connected in parallel with a function…

A:

Q: Match each type of transducer with the corresponding physical phenomenon, law, or property where it…

A: We are given with the following choices: Lorentz law Charge Faraday's law Ohm's law Capacitance…

Q: Calculate the RMS current through R2 in the diagram IR1 = 6.06mA peak, R2 = 2.7 kohms, total…

A:

Q: the value of impedance and capacitance for capacitor in figure 2 is

A:

Q: IMPEDANCE AND ADMITTANCE OF AC CIRCUIT WHAT ARE THE DIFFERENCE SHOW CIRCUIT AND TABLES

A: We need to tell about the difference between impedance and admittance .

Q: For figure (1)draw and calculate the voltages waveform across each half of secondary winding and…

A: The figure shows a full wave rectifier circuit using two diodes D1 and D2. The supply voltage is…

Q: 9) Find the reactance and the impedance of the circuit. Calculate the current and the resonance…

A:

Q: A solenoid with an inductance of 0.25 H and a resistance of 100 is connected to a 120-V 60-Hz…

A:

Q: If an electrical circuit draws 100W + J100VAR from a sinusoidal source, then what would the circuit…

A:

Q: Let's say you measure t1/2 to be 0.037  seconds and the resistance in the circuit is 68  Ohms. Then…

A: The half time, The resistance,

Q: 6. Determine the peak and average power delivered to RL in figure. 2:1 RL 220 N 120 V rms alll lelll

A: In this question,   We need to determine the peak voltage Across the load and average power P?  We…

Q: The maximum efficiency for pure inductance load and iron-losses = cupper losses is zero. O True O…

A: Given data,  For Pure inductive load , Resistance = 0. Given, iron losses = copper losses. For pure…

Q: Given the following Resistances and Inductors in Series and Voltage Source: R1 - 40 ohms R2 = 61…

A: we need to determine amplitude of the voltage across R1.

Q: An inductor and resistor are connected in parallel to a 120-V, 60-Hz line. The resistor has a…

A: An inductor and resistor are connected in parallel we need to find the phase angle between voltage…

Q: DI D2 AC D3 D4 R What is the waveform across D1? a) halfwave b) fullwave c) sinewave d) DC line What…

A:

Q: Please show you detailed solution Number 10 A voltage of 250 volts at 50 Hz is impressed on a…

A: In this question,  We need to choose the correct options What is power factor of the circuit.  We…

Q: In the figure: R1 = 1439.170, R2 = R1 and R3 =2R2, then determine the value of the voltage source E.…

A:

Q: If a circuit has a resistance of 3002 and a series inductance of 5002, what is the relationship…

A: The solution is given below

Q: A direct current (DC) of 4A flows into a previously uncharged 20 µF capacitor for 3 ms. Determine…

A: Given: Direct current, I=4 A Uncharged capacitor of capacitance, C=20 μF Time, t=3 ms

Q: If the voltmeter in the figure shown reads 60 V, find the following: A V V j3 + j4

A:

Compensation Techniques

The compensation techniques are the methods that are employed in the electrical control systems to enhance the performance of the system. The performance are generally affected by the factors like lag in the compensating devices, slow response of the system of the components like sensors used in the control system. The basic compensation technique involves lag compensation, lead compensation or the combination of the both.