Given the following elements of a T-beam: Length = 4m Flange thickness = 110mm Width of the web = 310mm Effective depth = 460mm Concrete strength = 30MPa Steel Yield strength = 414MPa If the beam is reinforced for tension only, determine the following: a. The balanced steel area b. The nominal and ultimate balanced moment capacity c. The maximum steel area d. The nominal and ultimate maximum moment capacity e. The required Steel Area to carry MDL= 120kN.m, MLL-60kN.m

Q: Example 2: At a cross section in a T-beam with flange width b= 600 mm, effective depth d=375 mm,…

A:

Q: Determine the permissible ultimate moment capacity Mn of the prestressed bonded beam shown in…

A: The yield strength of the prestressed tendons is fpy=240000 psi.The ultimate strength of the…

Q: A rectangular beam has width 300 mm and effective depth of 450mm .The beam reinforced with four 028…

A:

Q: A beam is loaded with the following service loads: Moment due to Dead Load = 282 kN-m Moment due to…

A:

Q: Directions: Check the safety of the typical reinforced concrete tee beam used to support the…

A:

Q: With a parabolic tendon, the rectangular concrete beam (800×400mm) shown below prestressed, So, it…

A: assumption in PSC-  at any section plane section before bending remain plane after bending.  within…

Q: d Craked Section 1. A doubly reinforced beam ha

A:

Q: under the following boundary conditions (x = 0, y = 0); (x = L, y = yMax). what kind of beam is…

A: Beams can also be described with their boundary conditions. In the given question,  When x=0…

Q: 2) As shown is the partial plan of the corridor of a certain building. If live load is 4 KPa and…

A:

Q: A rectangular beam has a width of 267mm and an effective depth of 495mm. It is reinforced with…

A:

Q: ) For a simply supported singly reinforced concrete beam of width b and effective depth d show that…

A: Assuming x=depth of the neutral axis As per BS 8110: C=AC×0.45fcuAC: Area of…

Q: A single span beam which carries a uniform load of 30kN/m has an unsupported span of 5m. It is made…

A: Uniform loadUnsupported spanCompressive load at centroidWooden sectionAllowable stresses (80% stress…

Q: 1.4 A rectangular beam has width 300 mm and effective depth of 450mm.The beam reinforced with four…

A:

Q: Assume Grade 50 steel and use f. = 5,000 psi for parts (a) thru (b). (a) The beam below is subjected…

A:

Q: Two designs for a beam are to be considered. Determine which one will support the loading shown…

A:

Q: problem 7: Check whether the depth of a simply supported beam in the following case is Hequate or…

A:

Q: The steel beam has the cross section shown. The beam length is L- 28 ft, and the cross-sectional…

A: A loaded beam and it’s cross section have been given in the question and it has been asked to…

Q: The following T-Beam has given properties: Effective Depth (d) = 485 mm, thickness of the slab = 100…

A:

Q: Using the Portal Method, determine the Moment Reaction at point B of the given Frame. Answer should…

A: consider shear force in internal columns twice those of outer ones.

Q: Problem 4. Calculate the moments of inertia of the given built-up section with respect to the x- and…

A: A composite crossection is given as follows

Q: (a) the maximum tensile bending stress at any location along the beam (enter a positive answer), and…

A: W= 40 kN/m Rb+Rd=40x4.5  Rb+Rd=180 kN Moment about D=0 ∑MD=o;Rb x 4.5 -40 x 4.5 x3.75 =0Rb=150 kN…

Q: nsidering BOTH strength and deflection criteria in approximate truss design, what would be the…

A:

Q: Design economical spacing of 10 mm diameter stirrups for the beam which carries the loads shown.…

A: d(effective depth) =430mm = 430/25.4 =16.93"

Q: Note: please use set B data 2° 3 MB A C 4m 2 m The cantilever beam above is made up of concrete with…

A: Given  A fixed beam  Required  Moment reaction at Support A

Q: P = L1 = L2= L1 Your Answer: P 195 2.50 4.5 Answer KN m m L2 ▷ View hint for Question 1 P The…

A:

Q: Five planks (4@ 40 x 40 mm and 1@ 40 x 380 mm), are joined together to form the l-section shown.…

A:

Q: 1. A rectangular beam has uniformly distributed dead and live loads along its full length as shown…

A:

Q: H.W2: Girder as shown used to carry load 90 kN subjected by eccentricity column 0.5 m, b = 250 mm, h…

A:

Q: Calculate the ultimate moment capacity of the beam whose width is 400mm and effective depth d = 700.…

A: Given:Compression steel area=1953 mm2Tension steel area=4784 mm2Effective depth=700 mmwidth of the…

Q: 2)The reinforced concrete beam has an effective span of 10 m and carries uniformly distributed dead…

A: Introduction- Steel and concrete beams are structural components designed to carry transverse…

Q: AWT305 x 41 standard steel shape is used to support the loads shown. Assume w = 46 kN/m, LAB = 1.8…

A:

Q: Design the reinforcement of a rectangular beam to resist a dead load moment of 200kN.m (including…

A: Total moment = Dead load moment + Live load moment= 200kN.m + 300kN.m= 500kN.m

Q: Determine the flexural capacity of the given section of beam below. b=260 d=380 d'=80 fc'=27 fy=415…

A:

Q: A WT305 x 41 standard steel shape is used to support the loads shown. Assume w = 40 KN/m, LAB = 1.9…

A:

Q: If the angles of a traverse are turned so that the 95% error of any angle is ±3.5″ what is the 95%…

A: calculate the 95 percent error as shown below :E95 =c×e  where , 95% in the error is E95…

Q: Check the adequacy of the isolated T-beam shown below according to ACI Code requirements and…

A:

Q: M=0.5kN.m A у P=2KN 5 KN m -0.25 1m 1.5m 0.75ml Choose an I-beam section that satisfies strength…

A: Given  σallowable = 22 MPA τallowable = 12 MPA ΣFy = 0 RA +RB = 2 + 0.25(0.75)            for UDL…

Q: The section of a Super-T prestressed concrete girder is shown below. The girder is simply supported…

A:

Q: 4. A reinforced concrete T-beam has b = 750 mm, t = 100 mm, d = 750 mm, bw = 350 mm, mm2, fc' = 20.7…

A:

Q: A WT305 x 41 standard steel shape is used to support the loads shown. Assumew = 42 kN/m, LaB = 1.5…

A:

Q: The following T-Beam has given properties: Effective Depth (d) = 485 mm, thickness of the slab = 100…

A: The values given in the question are as follows: Effective depth of T-beam(d)=485 mm Depth of flange…

Q: H.w.Draw S.F. & B.M.Diagrams For the Following Beam. 4 KN 2 KN 10 KN 3m Im

A:

Q: Design the reinforcement of a rectangular beam to resist a dead load moment of 200kN.m (including…

A: Design the reinforcement of a rectangular beam to resist a dead load moment of 200kN.m (including…

Q: AWT305 x 41 standard steel shape is used to support the loads shown. Assume w = 56 kN/m, LAB = 1.0…

A: To Determine Maximum Compressive and tensile stress.

Q: : Design the T-Beam section shown in fig. f'c-24 Mpa, fy=414 Mpa. L.L=24 kN/m D.L=15 kN/m -5m- -2 m-…

A:

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.