Given the circuit below with Vs = 15V, Rs = 1k2, R1 = 4KQ, and Vz = 10V:RsIR+ VR -wwwIz+VsVzRLVET.a)Verify if the diode will be ON or OFF, show your calculationsb)Calculate the voltage VL across and the current I through the load resistor R.c)Calculate the voltage VR across and the current IR through the resistor Rs.Pointsd)Calculate the current across the diode Iz.e)What is the type of diode used in the circuit above? Explain in your own words its operation?

Answered: Image /qna-images/answer/82dea8ed-2c29-4ef4-9acf-dd91c1aa02d1.jpg

Given the circuit below with Vs = 15V, Rs = 1k2, RL = 4K2, and Vz = 10V: Rs + VR - |Iz + IL IR Vs Vz RL T. a) Verify if the diode will be ON or OFF, show your calculations b) Calculate the voltage VL across and the current I through the load resistor RL. c) Calculate the voltage VR across and the current IR through the resistor Rs. d) Calculate the current across the diode Iz. e) What is the type of diode used in the circuit above? Explain in your own words its operation?

Given the circuit below with Vs = 15V, Rs = 1k2, RL = 4K2, and Vz = 10V: Rs + VR - |Iz + IL IR Vs Vz RL T. a) Verify if the diode will be ON or OFF, show your calculations b) Calculate the voltage VL across and the current I through the load resistor RL. c) Calculate the voltage VR across and the current IR through the resistor Rs. d) Calculate the current across the diode Iz. e) What is the type of diode used in the circuit above? Explain in your own words its operation?

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is the difference between a diode and rectifier?
What is CEMF?
Q4) Determine and sketch the output voltage across the load resistor (RL) for the circuit shown below. (assume Si diodes) V_DC 0.75 0.25 V_SIN Y SIN as RL -1 v SOR V_SQR 0.75 -0.75 V_TRI V TRI as
2. Figure A.1 shows I-V characteristics of two diodes, namely A and B. Diode A has higher dynamic resistance than diode B. UTM &UT ID 4 5UTM 3TM UTM UTM &UTM 5 UTM & UTM UTM 3 UTM 03 TM 6 UT 0.68 (a) UTM VD Figure A.1 State one possible reason why the diodes have different knee voltage values. UTM OM & UTM 3 UTM & TM (b) Based on Figure A.1, identify the knee voltage of UTM" TM 5 UTde BE UTM
consider the figure below that shows an approximated reverse recovery turn-off characteristics for a power diode. Show that the following relation can express the total reverse recovery charge, Qrr = 1/2(trr*ts1) di1/dt =1/2(trr*ts21) di2/dt * ip Isl 1s2! -Ir
b. using the conventional current flow, where is the direction of the current during the positive cycle at node A.c. Where is the direction of the current during positive cycle at node B.d. draw the output waveform(use the idea diode model)
perform dc analysis on a multiple diode circuit plz
Consider the circuit in the figure below 4:1 120 V rms ooooo gll reelee D₁ L a. What type of circuit is this? b. What is the total peak secondary voltage? D₂ c. Find the peak voltage across each half of the secondary. d. Sketch the voltage waveform across RL. e. What is the peak current through each diode? f. What is the PIV for each diode? RL 1.0 ΚΩ
The cut-in voltage for each diode in the circuits shown in Figure Pl.30 is V, = 0.6 V. For each circuit, determine the diode current I, and the voltage Vo (mea- sured with respect to ground potential). Q7 R= 10 k2 Vo oVo Ip R= 10 k2 5 V 5V 5 V 5 V (a) (b) R= 10 k2 Vo 5V E 5 V (c)
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp%3D20V, V1=3 V and V2=10 V. R D2 D1 Vin Vout V1 V2 Maximum voltage of output waveform Minimum voltage of output waveform Ps
In the clamping circuit below, assume the diode has Von-0.7V and V₁ is a sinusoidal wave with a peak-to-peak amplitude of 10V. How much is the maximum value of the output voltage signal (Vmax)? And how much will it be if we set V₂=2V? Input V1 C1 0.1e-6 9.3 V and 7.3 V 9.3 V and 11.3 V 11.3 V and 7.3 V O 7.3 V and 12.0 V O 12.0 V and 7.3 V Output D1 1N4148 .tran 30-3 V2 0 Vmax V(output) 0.0ms putput MAN Input 0.6ms 1.2ms V(input) 1.8ms 2.4ms 3.0ms