Given the below mutual coupled circuit with the stated current values below, what is the energy stored in mJ at 100 ms? Parameters: I₁ = 3/15 A, I₂ = 52-30 A, f = 60 Hz, L₁= 2.5 mH, L2 = 2.5 mH, M = 2.0 mH M i₁(1) i₂(t) v₁ (1) X 59.0 35.5 100. 25.6 3.8 87.6 L₁ 3 L2 None of these answers are correct v₂(1)

Q: A 120-V rms 60- Hz source supplies two loads connected in parallel, as shown in the figure. a) Find…

A: We are given,a) calculate power factor of parallel combinationb) calculate capacitance connected in…

Q: 1. The independent current source generates 0 current for t 0. + • 100 mH a. Sketch the current…

A: NOTE: as per our company guidelines we are supposed to answer only first 3 sub-parts. Kindly re-post…

Q: Ac - 100 Vrms R1 - 1k R2 - 500 Rload - 1k Capacitor - 2uF Q1. How much is the capacitor voltage…

A: To determine the phase lag between the capacitor voltage and the AC source voltage, we need to…

Q: Consider the circuit shown in Figure Q1(d), calculate the equivalent inductance, Leq at terminal…

A:

Q: An Inductor has an internal resistance of 10 Ohms and an inductance of 0.5H. What is it's impedance…

A: Given R = 10 ohm, L = 0.5H, F = 60Hz  To calculate impedance Z

Q: QS: For the coupled circuit shown in Figure 3, find the voltage across the capacitor of -j102…

A:

Q: The 0.5-nF capacitor of figure (1) has the waveform of current shown across it. Calculate and plot…

A: Current waveform is applied to the capacitance.  Find the voltages waveform and power waveform.

Q: The waveforms below represent one full cycle of the applied voltage vs and the supply current is.…

A: We can tell phase nature of waveforms by observing their peak positions  with respect to time.

Q: Q2. Find the equivalent inductance Leg and capacitance CEQ for the partial circuits shown. .01 μF 50…

A:

Q: The Voltage across a 5uF capaCitors a500€ u given v. as velt): 5ootesoot a, Find the current torouah…

A: IC = C d/dt [Vc(t)]    C= Capacitance    IC = Capacitor current    Vc(t) = Capacitor voltage

Q: Q3] Design a circuit to produce an average voltage of 27V across a 102 load resistor from a 70V ms…

A:

Q: 1. You are an electrician working in an industrial plant. You discover the problem with a certain…

A: Given that: In an industrial plant, a machine has a defective capacitor and its rating is 10 μF and…

Fault Analysis

In an electrical engineering system, a fault is an abnormal electric current flowing through the system, and fault analysis is the study of these faults. For instance, a short-circuit is a fault where the live wire touches the ground or neutral wire. If a circuit is interrupted by a failure of a current-carrying wire then an open circuit fault occurs. The open-circuit faults are also called series faults. One or more phases or ground may be involved in a three-phase fault or may occur only between two phases. Current flows into the earth in case of a ground fault or earth fault. For most situations, the prospective short circuit current of a fault that is predictable can be calculated. To limit the loss of service because of a failure, the protective devices can detect fault conditions and operate circuit breakers and also other devices. All phases equally can be affected in a poly-phase system which is known as symmetric electrical fault. The asymmetric fault becomes more complicated to analyze if only some phases are affected. By using methods such as symmetrical components, the power system analysis of these types of faults is often simplified. The main objective of power system protection is to design, detect, and interrupt power system faults.