Draw the free body diagram and solve Given: The 100-kg uniform rectangular plate is supported in the position shown byhinges A and Band by cable CD. The hinge at A can support an axial thrust (thereAy), but the hinge at B cannot (there is no By reaction).can be a non-zeroD450 mmA90 mm675 mmBC690 mm90 mmy270 mmFind: the reactions at the hinges and the tension in the cable.

Consider the free body diagram of the system as shown below.

Given: The 100-kg uniform rectangular plate is supported in the position shown by hinges A and B and by cable CD. The hinge at A can support an axial thrust (there can be a non-zero Ay), but the hinge at B cannot (there is no By reaction).

Given: The 100-kg uniform rectangular plate is supported in the position shown by hinges A and B and by cable CD. The hinge at A can support an axial thrust (there can be a non-zero Ay), but the hinge at B cannot (there is no By reaction).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Find the equivalent mass (equation) if it were placed at point B.

A: Find

Q: Problem Statement Based on Problem 5-74 from the textbook. The bend rod is supported at A, B, and C…

A: Draw the free-body diagram of the bend rod.

Q: 3m 2m B 2000 N A 1500 N 3

Q: Determine the magnitude and direction with respect to the +x-axis on the reaction at A and at C.…

A: For the given figure, a 2.4 kN-m moment and a 3 kN load ia acting. It is required to determine the…

Q: Given the figure at the right, find the resultant of F1 and F2 (in vector form)

Q: kg ånd thE the moment of intertia about Z axis.

A: calculate the mass moment of inertia about z axis at a distance x=0.4

Q: Given the Horizontal wood member shown that weights 38 lbs/ft and supports three vertical loads F1 =…

Q: Problem Statement Based on Problem 4-151 from the textbook. The pipe assembly is subjected to the…

A: Given: Here is the given data, Force, F=31.7 N To determine: The system to indicate the position of…

Q: The operation of the fuel pump for an automobile depends on the reciprocating action of the rocker…

Q: Problem 3: If the springs shown each have an unstretched length of 48 inches, determine the angle…

Q: Determine the reactions at the pin support and the applied moment if the bar of Figure 3 has a mass…

Q: A 4807 lb forklift used by Multi-National United is holding a 213 lb wooden block and z 49in. 213…

A: Given Data: Weight of forklift, 4807 lb

Q: 3. Determine the reactions at the pin support and the applied moment if the bar of Figure 3 has a…

A: Any item in static equilibrium is at rest since there is no net force acting on it. EQUILIBRIUM…

Q: draw the shera and moment diagram of the figure use ghaphical method

Q: Figure F4-11 Full Alternative Text F4-12. Determine the components of reaction that the thrust…

Q: II. Draw the free-body diagram of parts A, B, C, D and E of the following structure:

Q: The sphere shown in Figure has a mass of 6 kg and is supported as shown. Draw a free body diagram of…

A: The sphere shown in Figure has a mass of 6 kg and is supported as shown.Draw a free body diagram of…

Q: 25 m 1.5 m For the hinged door shown in the figure: a) Determine the magnitude of the moment Fe 250N…

Q: The tractor shovel shown ,carries a 530 kg load that has its center of mass at HH. The shovel’s…

A: Sol:-For the given figureFree Body diagram of tractor shovel∵tanθ=cb=306204θ=56.31°For equilibrium,…

Q: Can you give me the free-body diagram?

A: Given data:- A pendulum of mass M1=1 kg length L = 0.75 m . Mass of Block M2= 2 kg To find :- Free…

Q: Problem 5.2

A: A free-body diagram is a method to analyze the external forces and reactions acting on a given body…

Q: Calculate the force and moment reactions in the fixed support at point O. B 100 lb 25' 2292 100 lb…

A: The weight force of the different signals panels is: WB=-100 lb kWC=-100 lb kWD=-100 lb k

Q: A 11 in 40° B b E D a G 7 in 4 in F

Q: The mobile crane is symmetrically supported by two outriggers at A and two at B in order to relieve…

Q: Problem 1: Replace the force system by a wrench. Also, find point P where the wrench intersects the…

Q: Part A The mobile crane s symmetrically supported by two outriggers at A and two at B in order to…

A: A crane and truck arrangement is given. To find out the free body diagram of the given arrangement.

Q: 4. The access door in Fig. P6-13 is held in the position by cable AB. If the magnitude of tension T…

Q: Draw the free-body diagram of AC

Q: The figure below are two discs D and E which have a mass of 200 lbs and 100 lbs, respectively. If P…

Q: 5.33. The roller shown in Fig. 5-32 weighs 339 lb. What force T is necessary to start the roller…

A: The angle alpha is-

Q: Generate free body diagram for the following mechanism:

A: Given data: The mass of the block hanging at point B is m. The vertical load due to the weight of…

Q: Bx and by in the free body diagram are wrong

A: Here you are saying that Bx and By in the free body diagram are wrong.

Q: Based on the attached figure: Determine the x and y components of reaction at ‘C’ using scalar…

Q: For the truss loaded as shown, determine the equation for the line of action of the stand-alone…

Q: Determine the moment reaction at A. MA = Blank 1 kN-m Blank 1 Add your answer Determine the vertical…

Q: DENIMUI 2: This fuel pump uses the reciprocating action of rocker arm ABC. The arm is pinned at B…

A: Given data :- Force at point A (FA)= 60 N Force at point C (FC) =125 N To fond :- force acting at…

Q: A woman is holding a 3.7-kg sphere in her hand with the entire arm held horizontally as shown in the…

A: The mass of sphere is .The mass of upper arm is .The mass of lower arm is .The mass of hand is

Q: Q6. What is the stress concentration for normal stress due to bending at the critical location?…

A: Option - D => 1.4

Q: The system above is supported by a ball-and-socket joint at point A, as well as cables BC and BD. A…

Q: L3 L2 A load weighing P kN with AB, AC and AD cables such as are carried. Points A and B are x-axis,…

Q: 5-4 Locate the center of mass for the four particles shown. in Fig, P54 if m= 16 kg, mg = 24 kg, mc…

A: Given data: The center of mass of each particle with respect to the origin is

Q: consider the rotational axis at the point where the tire contacts the ground, directed perpendicular…

A: A man is pulling a wheelbarrow to lift the weight. A wheelbarrow is a vehicle to lift weight…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

Draw the free body diagram and solve

Given: The 100-kg uniform rectangular plate is supported in the position shown by
hinges A and Band by cable CD. The hinge at A can support an axial thrust (there
Ay), but the hinge at B cannot (there is no By reaction).
can be a non-zero
D
450 mm
A
90 mm
675 mm
B
C
690 mm
90 mm
y
270 mm
Find: the reactions at the hinges and the tension in the cable.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 11 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A wheel radius 0.4meter has mass 3kg se figure. Center of wheel goes a rope to point A, the wheel has contact with the edge of the table in point B. An mass of 2kg is hanging from the edge of wheel in point C. Find the tention force for the rope attached in the centrum of the wheel.and point A
P4b please help me with the answer and full solution
Please don't provide handwritten solution ....
The round stepped shaft (diameters d and D) shown below is a design for an exoplanet rover wheel axle. Assuming the wheel is stuck, a torque from the motor is transmitted to the axle but it is not rotating. The reaction of the weight of the rover on the ground and the torque the wheel applies to the ground are represented by the force F acting in the center of the wheel hub (not shown) at point C. There is a sharp fillet at B with radius r shown below. Bearings are shown at point A and next to point B. You may assume the bearing at B resists the bending moment caused by the force F and acts like a fixed reaction. В A L2 L1 T L3 - ØD Ød R. r F SUBMIT ANSWERS HERE: Paramete Parameter Value Value SUT (tension) 400 MPa | L1 400 mm Suc (Compression) 600 Мра L2 200 mm Sy 380 MPа L3 100 mm 600 N-m ø d 40 mm F 0.2 kN ø D 55 mm R. r 8 mm
Statics
A person is performing slow arm curls with 10-kgWeight as idicated in the left image of the figure below. The biceps group (consisting of the biceps and brachialis muscles) is the major factor in this exercise. Determine the magnitude F7 of the biceps group force and the magnitude 4 of the elbow joint reaction at point E for the forearm position. The free body diagram is shown in the right image of the figure. Take the dimensions shown to locate the effectivepoints of application of the biceps group; these points are 200 mm directly above E and 50 mm directly to the right of E. Include the eftect of the the 1.5-kg forearm mass with mass center at point G. Assuming that humerus is perfectly vertical and fixed; therefore, the elbow joint E is acting like pin connection. The forearm (E-B-G-C) is perfectly horizontal; therefore, the angle A-E-B is 90 deg.
Mechanic
#1-A rod 15oom Cong Matates in a horizmtal plane about a vertical axis thru its center. At ench end f the rod is fastened a' cord o.800m long Each cord kupports a weight W. Find the Epeed f hotation 'n' to ircline each rpm cord at 32° th the verfical. #2 Given: W= 250 N Regis : aー 6-T L-0-800m C- time for | rev.
3/11 Find the angle of tilt 0 with the horizontal so that the contact force at B will be one-half that at A for the smooth cylinder. Ans. 0 = 18.43° B. A 45° 45° Problem 3/11
4-2) Find the megnitude and direction of the support forcas at A and B and the res tant mament
If the mass of cylinder is 100 kg, find the tension developed in wires AB and AC and find the support reactions in point O.. 3 m 1.5 m to 1.5 m 3 m B 1 m
2m dz - m. None of them اپن For the robot above, please determine Uo (the potential energy of Link #0) OU 9.8 OU = 5.6 OUo = 4,9 OU=19.6 * d₁, d₂ and ₂ are the joint variables m₂ = m₁ = m₂ = m₂ = 1 kg The moment of inertia of the last link is 3 kg.m². The mass centers are located on the middle point of each link.