Given that M and O = 1200N, T and S = 950N, P and N = 1050N, and assuming that the members of the truss have negligible mas... A) Draw the FBD of the system shown. B) Calculate the magnitude (N) and direction of the reaction of the support in A. C) Calculate the magnitude (N) and direction of the reaction of the support in B. Express your answers in 2 decimal places. M mathalino.com 30° 30° 3 m 3 m 3 m mathalino.com

Q: The wind speed beyond which the turbine should stop its operation is triggering speed cut-in speed…

A: Cut out speed, wind speed beyond cut out speed, the turbine should stops its operation. Every wind…

Q: Describe how the wind turbine works.

A: The wind turbine as name suggests, the main energy sources comes from kinetic energy of the wind.…

Q: What kind of situation might happened to the engine due to too high temperture?

A: Let us discuss effects of high temperature on engine.

Q: If the mass flow rate can be expressed as m=PAV, then the averaged velocity should be O A.…

A: Given data:- Mass flow rate (m)=ρAV Where, ρ= density of flowing fluid A= area of flowing system V=…

Q: Give a concise introduction on Self pressurizing reservoirs

A: Self pressurizing reservoirs :-

Q: I need the answer for problem number 14.

A: 14.In this drawing, only one chamfer is represented by the leader line. The chamfer is represented…

Q: Describe the process of Feedforward Regulation system?

A: In feedforward regulation system controller identifies the errors within the system before output…

Q: Explain and give details about Run to failure strategy under plant maintenance

A: The Run to failure strategy is the simplest maintenance strategy. In this strategy assets are…

Q: Welding would fall under the ___________________ type of certification.

A: Many certifications are available for workers based on their skills, type of industry, etc.

Q: There can be more than 1 answer per item What is the purpose of having piston ring gaps? So that…

A:

Q: Engine working principle

A: ENGINE WORKING PRINCIPLE: A engine is a machine, which converts heat energy into mechanical energy.…

Q: Consider the simple pendulum in the figure. The pendulum is released at point A, swings through its…

A: At the highest point of its motion, kinetic energy is minimum (i.e. zero) and potential energy…

Q: Define what is octane number and discuss its relationship with engine knocking.

A: Octane number is a measure of the knock resistance in a gasoline engine. Its value ranges from 0 to…

Q: The specific heat capacity value is generally high for _________ a. polymers b. ferrous metals c.…

A:

Q: what is the temp gradient and direction

A:

Q: What is a freeze frame

A: Freeze Frame: At the point when a PC or framework (PCM) distinguishes a mistake and the Check Engine…

Q: Explain this diagram

A: Given:To find:Explain the diagram.

Q: Write the advantages and disadvantages of gus turbime

A: Required:Advantages and disadvantages of gas turbine

Q: Does the velocity change across a stator?

A: Yes, the velocity change across a stator.

Q: Explain the the fan design procedure?

A: Given Fan Design To find Design procedure of fan

Q: Provide a general description of the type of furnace

A: A furnace is a device that produces and transfers heat to materials with the goal of causing…

Q: 1.Name type of failures in engine blocks

A: The engine is the most important part of the IC engine. In production, Every company produces an…

Q: Give any four significance of API Standard

A: American Petroleum Institute (API) Standard:-  American Petroleum Institute of standards Improve…

Q: List any four limitations of using conventional energy sources

A: There are two main sources of energy which can be written as below, 1. Source of conventional type…

Q: Write down the name of Primary Control Surface

A: The rudder is a fundamental control surface which is typically controlled by pedals rather than…

Q: Enumerate the various welding process.

A: It is required to enlist various welding process

Q: An ammonia compressor has a volumetric efficiency of 85%, operating condensing & evaporating…

A:

Q: ot

A: introduction: This can be accomplished in one of two ways: through air cooling or through liquid…

Q: State at least 3 laws related to thermocouples and explain them briefly with sketches and…

A: Thermocouple topic given

Q: Draw the primary and secondary auxiliary views. FRP PRP

A: According to the given data.There is two view of the object.We need to draw the auxiliary view of…

Q: Make decisions concerning needs and types of ventilation for acceptable indoor air quality?

A: The types of ventilation is given.

Q: What is FRL Unit?

A: The abbreviation FRL stands, F for the filter, R for the regulator, and L for the lubricator. Thus…

Q: The pressure vessel shown has diameter 7.8 (in) and thickness 0.164 (in) and is made of steel with…

A: Given: The diameter of the pressure vessel is d=7.8 in The thickness of the pressure vessel is…

Q: How can we prevent and control noise pollution in the workplace?

A: Reducing noise pollution in the workplace Change or modify equipment. Locate the equipment in a…

Q: HINERY CO. LTD. FISCLAIMER

A: Explaining the type of engine, a number of strokes and the manner of ignition.

Q: What do you mean by intake stroke?

A: Intake stroke: It occurs when suction occurs due to downward movement of piston in an internal…

Q: Briefly explain the galvanizing process with a neat diagram. b). Write the applications of…

A: a) Galvanizing Process. Galvanization or Galvanizing is the process of applying a protective zinc…

Q: 10. The principle advantages of air flat plate over a liquid flat plate collector are: A. It is…

A:

Q: or safety of plant which department is responsible?

A: Given Data⇒ Department Safety of plant

Q: Explain brief history of ic engine in your own words.

A: In 1791, a scientist John Barber made a gas turbine. After three years, Another Scientist Thomas…

Q: The optimum effective temperature for human comfort is ?

A: For a human being,

Q: PV ________ is a group of PV __________ .     Select one: module; Panels Array; Panels…

A: A group of PV cells connected electrically and placed into a frame is called a module (or a solar…

Q: Compressed air can be used to clean the machine, is a general safety precaution while working in a…

A: It is important to follow the safety guidelines while working in a workshop. They are provided in…

Q: 7- Differentiate SFC and TFC?

A:

Q: One of the type of Tunnel washers is 777 b 17 Od Top transfer Forward tilt Side load Auto carte…

A: Tunnel washer: A tunnel washer, also known as a continuous batch washer, is a large industrial…

Q: Which one of the following statement is correct for steam nozzle? O a. Outlet velocity of the steam…

A: Let us first understand how steam nozzle works: Steam nozzles are generally used in power plants…

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.