Given that Jamie worked 50 hours (Hours = 50) last week and earns $10.00 an hour (Rate =10), how much did Jamie earn last week, before taxes (TotalPay)? If (Rate >=10) OR (Hours <=40) Then TotalPay Hours * Rate Else TotalPay (Hours * Rate)+(Hours-40)*Rate* 1.5 End If a. $ 500 b. $ 650 c. $750 d. $ 400

Q: need the answer quickly

A: Traverse ABCDAAzimuth.AB=120°14'BC=40°20'CD=300°15'DA=200°10'

Q: 3.33 The following data are obtained from a tensile test of a 12.7-mm-diameter aluminum specimen…

A: As per the Guidelines of Bartleby We are supposed to answer only first three subparts. Ultimate…

Q: A tube is used as a siphon to discharge an oil of specific gravity 0.8 from a large open vessel into…

A: Since the question comprises of a number of subparts, the solution for first 3 subparts is as…

Q: _n-coil with a temperature of 6°C and leaves it -pipes system shown in the figure below.

A: Given:- temperature=6 degree celcius change temperature=12 degree celcius To find:- diameter of all…

Q: . A solid cylinder of length L and diameter D and specific gravity 0.6 floats in neutral equilibrium…

A: For neutral equilibrium  GM=0 Specific gravity g=0.6 (Given)

Q: Draw the front section, horizontal projection, and side projection MB 42 30 28 14 40 2oma R22. 21 25…

A:

Q: ) To tal density b) dry densiz y =)degree of saturation )saturated densizy (assume no volume change)

A: This question has been taken from geo technical engineering

Q: Rainfall of intensity 20mm/h occurred over a [wa watershed of area 1km2 for duration of six hours.…

A: Given  Rainfall intensity = 20 mm/h  Area of watershed = 1km2 = 106 m2  Duration of rainfall = 6h…

Q: The block is deformed into the position shown by the dashed lines. Determine the average normal…

A:

Q: A circular column of a cross-section (460)mm in diameter is reinforced with 6 bars of ($25mm), with…

A: Axial force : The force operating on a body in its axial direction is characterized as axial tension…

Q: Newton Raphson Method is used to find the Roots of the equation x + 2x2 + 3x-1 0 If the initial…

A:

Q: For the state stress shown in figure below, determine the principle stresses and the maximum…

A:

Q: For the composite structure shown in Figure (3), use the unit load method (virtual work method) to…

A:

Q: A soil yielded a maximum dry unit weight of 18 kN/m3 at a moisture content of 16% during a Standard…

A: Given, G = 2.65 Moisture content, w= 16% Dry unit weight = Yd = 18kN/m³ Degree of saturation = ?

Q: Example 2.5 An oven dry soil sample of volume 250 cc weighs 430 g. If the specific gravity of solids…

A:

Q: 6. In a pipe of 200 mm diameter the maximum velocity of flow is found to be 1.5 m/s. If flow in the…

A: Diameter of pipe = 200mm  Radius of pipe = 100mm or 0.1m MAximum velocity of flow (Vmax) = 1.5m/s To…

Q: 8.1: Use the virtual work method to determine the horizontal and vertical deflections at joint B of…

A: Due to issue in Math type , providing handwritten solution

Q: For a data of maximum recorded fiood of a river, the moan and standard ation are 4200 m/s and 1705…

A:

Q: The regression analysis of a 30 year flood data at a point • on a river yielded sample mean =…

A:

Q: Problem 1: The tanker carries 858000 barrels of crude oil in its hold. Determine the weight of the…

A: As per guidelines we need to answer only first question so please repost rest questions separately.

Q: Detremine the slope and deflection of point C and D . El is constant . Use conjugate beam Method 60…

A: Given data: The length of span AD is 3m, span DB is 3m and span BC is 3m. The point load acting on…

Q: H.W. Problem Air at 20 C flows at a velocity of 2 m/s across a rectangular flat plate. The plate is…

A:

Q: رشت متار فيامین( (2 Forthe beam shown, a. draw sFD and BMD, b. prove that for the isosceles:, Tnax.…

A: As per company's guidelines we can only answer first three questions.  Kindly post other questions…

Q: Question 3: Is it possible to fit a cation Ct of radius 180 pm in the tetrahedral site of the…

A:

Q: Qin 1 0.2 m3/s 3 0.3 m3/s Q3 Q4 2 4 Q in Qout = 0.5, Q3= =

A:

Q: A sketch of a transformed flow net in x-direction under a dam is shown in Figure, the soil has k…

A:

Q: :Compute the volume using the prismoidal formula and by average end areas for the following…

A: h = 5.3 ft, h1 = 7.4 ft , h2 = 7.8 ft, b = 24 ft, b1 = 23 ft , b2 = 23.7 ft Let A1 = Area of station…

Q: A cantilever retaining wall is required to support a backfill having the following soil properties:…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: [4]. Determine the force in members JE and GF of the truss and state if these members are in tension…

A:

Q: A flat plate of area 1.5 x 10^6 mm? is pulled with a speed of 0.4 m/s relative to another plate…

A:

Q: Q5/ Find job mix formula by using mathematical method. Aggregate Specification Sieve Size A B C…

A:

Q: The pressure head at level AA is 0.091 m of water, and the unit weights of gas and air are 5.50 and…

A: given data water head at AA=0.091m unit weight of air=12.35N/m3 unit weight of gas=5.5N/m3

Q: Problem 2: A 0.10 m^3 volume of water is observed to be 0.0982 m^3 after a pressure is applied. What…

A:

Asphalt Binders and Mixtures

Asphalt binders are subsidiary products procured during the refining process of petroleum while manufacturing gasoline, diesel, and similar petroleum products. Asphalt binders are obtained from the residue that remains after the distillation of petroleum, this residue is further subjected to steam distillation and oxidation to remove the traces of gas oil present in the residue. Certain additives or modifiers are also added to asphalt binders to alter them to suit different applications.