GIVEN: REQUIRED: (a) Establish the Current Equations at points x, y and z (b) Establish and simplify the Voltage Equations taken at Loop 1, 2 and 3 All Voltage sources (V) = 4 V (c) Determine the Branch Currents: 1, l2, 13, las, l67, la R7 = 20 V RS - 40 R6 - 20 le7 R4 - 20 l45 V V V R2 - 40 V R1 -40 V V R3 - 20 2 Is V V ref R8 = 40 十十

GIVEN: REQUIRED: (a) Establish the Current Equations at points x, y and z (b) Establish and simplify the Voltage Equations taken at Loop 1, 2 and 3 All Voltage sources (V) = 4 V (c) Determine the Branch Currents: 1, l2, 13, las, l67, la R7 = 20 V RS - 40 R6 - 20 le7 R4 - 20 l45 V V V R2 - 40 V R1 -40 V V R3 - 20 2 Is V V ref R8 = 40 十十

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Circuits star triangle transformation? RT? Rbd? Rde?Red?
R1 = 50 ohm R3 R2 RI R2 = 25 ohm I2 El = 5 volt R3 = 75 ohm E2 E2 = 4 volt [Q3] Analyze the following electrical circuit by finding the currents (I1, 12 and I3) using Gauss-elimination method
Calculate ( C ) Load current, Calculate ( D ) Power in the load resistor or Power in the 50 ohms resistor, Calculate ( B ) Rth, Calculate ( A) Vth
R1 = 18 Q A R2 = 9 0 12 2.5 A VT = 97.5 V R4 = 14 Q R3 = 16 0 R5 = 7 Q R6 Determine: R6 = PT = %3D 11 %3D 14 = 15%3D 16 = IT = V2 = V3 = V4 = CamScanner
Procedure: Vcc = 20V 1. Connect the circuit shown in Figure. 2. Measure VB, VE, VC and VCE R, = 22 k2 3. Measure the voltages VR1 and VR2. Calculate the currents 11 and 12 using Ohm's Law. Rc = 3 k2 4. Using Kirchhoff's current law, calculate the current IB. Then, measure the currents IE and IC values. IB R, = 6.8 k2 1, IE %3D RE = 680 2 5. Confirm that IB calculated using KCL is equal to the IE-IC 6. Please come out with your own tables to record the measured data. www ww
II R. R A potentomeer with a restve load showing equivalent tred restitors tor cianty Given Vs- 120v RI + R2- Potentiomenter R-90 ohma Ri - 60 ohm Calculate the power delivered Ri when the slider is a) On top of RI (Node 'A) b) Moved down 13 or / at node B o Moved down 23 or/at pode C
Find: a. Branch currentsb. Total current drawn by the circuitc. Total power drawn by the circuitd. Total power factor of the circuit Please show complete solution and draw the circuit diagram. Please round off answers up to the 3rd decimal places. Thank you!
Determine the Branch Currents using Mesh Currents: a.) Branch ab b.) Branch ac c.) Branch bc NOTE: The unit of resistance is in ohms and the unit of the voltage supply is in volts.
Solve by applying Millman's theorem, apply D.V.V and D.V.C where can be applied. a) Find all b) Power balance c) LVK on meshes and LCK on main nodes d) Mark the currents and their direction e) Mark the voltages and their polarity f) elaborate the oriented graph of E0
Problem 3. Referring to figure shown below, determine the following using Nodal Method: (use a reference node "d") a. Nodal Voltage Va, Vb, Ve and Va if Va will serve as a reference point or zero potential. b. Branch current 11, 12, 13, 14, Is, and 16 502 + 9V 402 www - 12 202 ww 12V 10V 4|F 302 2 4V 602 www 13 С 6V
Consirder the circuit diagram below. Given I1 = 2 mA and I4= 6mA, find the currents I2, I3, I5 and I6. State your conclusion as a table of values.
with Kirchhoff's laws with the electric current shown in figure below, the following equations are found. Find the indicated currents (in A) I1, I2 and I3. a)I1=3.15A, I2=1.87A , I3=0.19A b)I1=0.15A, I2=2.87A , I3=3.19A c)I1=2.15A, I2=3.87A , I3=1.19A d)I1=1.15A, I2=4.87A , I3=3.19A