Given grade 60 steel rebar and 4000 psi normal-weight concrete, (a) What is the yield strength of steel? (b) What is the modules of elasticity of the steel? (c) What is the steel strain at the yield point? (d) What is the concrete compressive strength? (e) What is the concrete's modulus of rupture per ACI318-19? (f) What is the concrete' ultimate compressive strain?

Given grade 60 steel rebar and 4000 psi normal-weight concrete, (a) What is the yield strength of steel? (b) What is the modules of elasticity of the steel? (c) What is the steel strain at the yield point? (d) What is the concrete compressive strength? (e) What is the concrete's modulus of rupture per ACI318-19? (f) What is the concrete' ultimate compressive strain?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Concrete is required for a column that will be Severe Exposure to freezing and thawing. The cross section of the column is 300 × 300 mm. The smallest spacing between reinforcing steel is 40 mm. The specified compressive strength of concrete at 28 days is 40 MPa with a slump of 25 to 50 mm. The properties of materials are as follows: (a) Cement used is type I Portland cement with a specific gravity of 3.10. (b) The available coarse aggregate has a maximum size of 23 mm, a dry-rodded unit weight of 1800 kg/m3, a bulk specific gravity (SSD) of 2.68, absorption capacity of 0.65%, and moisture content (SSD) of 0.27%. (c) The fine aggregate has a bulk specific gravity (SSD) of 2.75, absorption capacity of 1.5%, a moisture content (SSD) of 2.5%, and a fineness modulus of 2.7,The aggregates conform to the ASTM C33-84 requirements for grading.
Q. Using the British methods, design a concrete mix to bear an average compressive strength of 35 MPa at 28 days, to cast a room slab with the following dimensions (5 width x 4 length x 0.2 depth m) and 200 mm space distance of reinforcement. Consider the following properties: o Cement used is type I Portland cement ® Required slump = 30 — 60 mm o Coarse aggregate: ® Crushed rocks * Maximum size of 40 mm, e The fine aggregate: * Crushed rocks = Falls in zone 3 o Assume zone A for figure 1 o AssumeK = 1.64
Design the concrete mix according to the following conditions:Design EnvironmentPavement slab, subjected to freezingRequired design strength = 21 MPaSlab thickness = 300 mmStatistical data indicate a standard deviation of compressive strength of1.7 MPa is expected (more than 30 samples).Only air entrainer is allowed.Available MaterialsAir entrainer: Manufacture specification is 9.5 mL/1% air/100 kgcement.Coarse aggregate: 2 in. nominal maximum size, crushed stoneBulk oven-dry specific gravity = 2.573, absorption = 2.8,Oven-dry rodded density = 1922 kg/m3Moisture content = 1,Fine aggregate: Natural sandBulk oven-dry specific gravity = 2.540, absorption = 3.4,Moisture content = 4.5,Fineness modulus = 2.68
10
What is the target mean strength (N/mm²) of the M30 grade concrete, if the standard deviation is 5.0?
Design the concrete mix according to the following conditions:Design Environment• Building beamo Required design strength = 27.6 MPao Minimum dimension = 150 mmo Minimum space between rebar = 40 mmo Minimum cover over rebar = 40 mmo Statistical data indicate a standard deviation of compressive strengthof 2.1 MPa is expected (more than 30 samples).• Only air entrainer is allowed.• Moderate Sulphate exposure.• Available Materialso Air entrainer:▪ Manufacture specification 6.3 mL/1% air/100 kg cement.o Coarse aggregate:▪ 19 mm nominal maximum size▪ River gravel (rounded)▪ Bulk oven-dry specific gravity = 2.55▪ Absorption = 3.6▪ Oven-dry rodded density = 1761 kg/m3▪ Moisture content = 2.5o Fine aggregate:▪ Natural sand▪ Bulk oven-dry specific gravity = 2.659▪ Absorption = 0.5▪ Moisture content = 2▪ Fineness modulus = 2.47o Cement▪ Type II (Moderate Sulphate Resistant)▪ Specific Gravity = 3.15Based on this information, find the following and summarize the findings in a table d) The amount…
Which one of the following sentences is not correct? a. For many years, tensile strength has been measured in terms of the compressive strength. b. The modulus of rupture where the normal-weight concrete has an fc of 4000 psi is 474 psi. С. For lightweight concretes tensile strength depends largely on the porous aggregate. d. For normal weight concrete, the tensile strength depends primarily on the strength of bond between hardened cement paste and aggregate. 13:54
4b. Deformation occurs on freshly lay concrete when it finally set or harden.discuss the various causes for dimensional changes in the hardened concrete.
A1-What is the bond strength between steel and concrete and how it can be calculated? 2-What is the segregation of fresh concrete? Give its reason and how to control it? V3- What are the advantages of concrete? 3- Discuss the effect of age and curing on the compressive strength of concrete. 5-What are the main purposes of using plasticizer admixtures? 6-What are the main techniques that should be used to reduce heat of hydration in mass
Compare the compressive strength and the splitting tensile strength.of following concrete.