Given:Starting Height H = 2.50 metersstarting angle = 43.0°. Starting velocity = 8.3 m/s●●Find:• maximum speed = _____ m/sWritten work: Find Vx max, Vy max, fill in Sqrt(Vxm^2 + Vym^2)Your Answer:

Answered: Image /qna-images/answer/ab3d5e16-acaa-482a-871b-92d1951bc860.jpg

Given: ● ● Find: Starting Height H = 2.50 meters starting angle = 43.0° Starting velocity = 8.3 m/s • maximum speed = _____ m/s Written work: Find Vx max, Vy max, fill in Sqrt(Vxm^2 + Vym^2) Your Answer:

Given: ● ● Find: Starting Height H = 2.50 meters starting angle = 43.0° Starting velocity = 8.3 m/s • maximum speed = _____ m/s Written work: Find Vx max, Vy max, fill in Sqrt(Vxm^2 + Vym^2) Your Answer:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A) B) Find and report the magnitudes and directions for w3 and w4. Find and report the magnitude and direction of the absolute velocity of point P on link 3. input : w, = 1 rad/s ccw link 4 = 110 cm %3D C 4 В P A 2 D 3.
The moment of the torpedo control unit in water was tested with a 1:8 scale scale model in a water tunnel of identical properties with a speed of 20 m/s if the measured moment in the model was 14 Nm. calculate 1) Determine the velocity of the prototype using the Reynolds number analogy. 2) Find the ratio of the forces occurring in the model and prototype. Using the analogy of Euler number 3) find the moment that occurred with the prototype.
Please do it Fast
Engineering Analysis. Plz help me help
Please ASAP: (image provided) a) Create a function to solve a projectile problem where you are given initial x and y velocity, and the initial and final y position (inputs). You would like to use this function to find the final x and y velocity (outputs). This function will be used in the solution of the following problem. b) In the figure below, belt A moves with a constant velocity of 5 ft/s, and discharges sand onto belt B as shown. Assume that the angle of belt B is 15 degrees as shown. Write a MATLAB program to determine the required velocity of belt B if the relative velocity with which the sand hits belt B is (a) vertical, and (b) as small as possible. For part (b), use MATLAB to create a plot of the velocity of the sand relative to belt B, as a function of the velocity of belt B. Verify (either by hand, or by using MATLAB) that the minimum shown in this plot corresponds to the point at which the velocity of the sand relative to belt B is perpendicular to the velocity of…
1) From 0 to 10 sec, find alphaA1, alphaC1 in rad/s^2, omegaA1(t), omegaC1(t) in rad/s, thetaA1(t), thetaB1(t) and thetaC1(t) in rad, and the distance made by the load s1 in inches and in feet made by the load during this time.
ull JAWWAL ? 6:20 PM @ 50% A moodle.najah.edu МOODLE Recent - For the following system, answer the following assuming each tension in cable = 10 kN 1) Express tensions in Cartesian coordinate system 2) Find moment due to both cables and weight of door= 1 kN about point A 3) Find moment due to both cables and weight of door= 1 kN about z-axis 960 mm 450 mm 90 mm 675 mm B 90 mm 690 mm 270 mm Fig. P4.113 II
The in-plane angular speed of the bent bar indicated below is w = 0.2 rad/s. The dimensions of the bar are L = 0.4 m and H = 0.6 m. Find the magnitude of the velocity (in m/s) of the endpoint B. H B L Figure is from "Engineering Mechanic An Introduction to Dynamics", McGill and King.
### Develop a conclusion of a piping design report for the choice of a pump, based on the calculated parameters of flow Q = 10 l/s, power of 10kw taking into account that the head of 60 mca adopted was higher than that calculated for safety, and that the pump was chosen through the WebCAPS catalogue of the company GRUNDFOS. The pump chosen was the GRUNDFOS CR 32-3 A-F-A-E-HQQE
Use t'=20.4 instead of 8.4 and use the formulas attached
answer correctly with clear solution