GivendF1/dP = 20 + 0.4P, dF2/dP = 30 + 0.4P2, andP;oss = 0.0004P? + 0.0006P?Assume the load = 1000 MW. Using the coordination equation method, and starting withPO= 500MW, P= 500MW Perform one iteration to get:Select one:a. None of theseOb.P = 775MW, P2 = 475MW, and) = 550$/MWhО с. Р. 3 675МW, P, 3 575MW,and^ — 450$/MWhO d. P1= 875MW, P2 = 375MW, and = 650$/MWhClear my choice

Given P10=500 MWP20=500 MW Coordination equation method

Answered: Given dF1/dP = 20 +0.4P , dF2/dP, = 30…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

Course:Power generation and control Please solve in detail to understand
Given dF₁/dP₁ = 20 +0.4P₁, dF₂/dP₂ = 30 +0.4P2, and Poss = 0.0004P2 + 0.0006P2² Assume the load = 1000 MW. Using the coordination equation method, and starting with P = 500MW, P = 500MW Perform one iteration to get: Select one: O a. None of these b. P₁ = 775MW, P₂ = 475MW, andλ = 550$/MWh O c. P₁ = 675MW, P₂ = 575MW, andλ = 450$/MWh O d. P₁ = 875MW, P₂ = 375MW, andλ = 650$/MWh
An AC circuit is shown in the diagram. The source of emf has a peak voltage of 9.00 V and a frequency of 60.0 Hz. Assume the wires contribute a negligible amount to the resistance and the AC source has negligible internal resistance. 524 2 493 2 1.56 k2 a) Find the equivalent resistance of the circuit. Redraw the circuit showing the equivalent resistor and use this simplified circuit for the rest of the problem. 315 2 Re = b) Find the rms current. 9.00 V, 60.0 Hz c) If the current is zero at time t= 0, find the first two times (after time t-0) that the current is equal to its rms value. and d) Find the average power dissipated by the circuit.
A 500 MVA synchronous machine has H, = 5.6 MJ/MVA and a 1200 MVA machine has H₂ = 2.0 MJ/MVA. The two machines operate in parallel in a power station. What is the equivalent. H constant for the two, relative to a 100 MVA base?
. For the circuit given in figure 6, find V_ ms and I_rms on R3. R, R3 ww 10 20 R4 R2 C 40 5Vp Figure 6 ww ww
please explain the operating principle of single phase 2S-2P PMSM based on 3D design illustration.
AC Circuits Current, Voltage, Power, Power Factor and Phasor Diagrams. Consider the circuit shown in Figure 3. (i) Find the total impedance ZT as seen by the voltage source. (ii) Find the total current IT supplied by the source. (iii) Sketch phasor diagram of Vs and IT and State whether IT leads or lags Vs (iv) Determine the power factor angle for the circuit. 9. L R1 1002 0.213H IT Vs R3 1502 C 12020°V 22µF 60HZ R2 50Ω Figure 3 Answers |(1) Zr = (ii) IT= (iii)
Figure 2 shows three "LC" circuits, two of them with capacitance capacitors "C" and the three with inductance coils "L", the three circuits are coupled by means of two capacitance capacitors "Cc". The currents that circulate through each mesh are those indicated in the figure: "I1", "I2" and "I3". Using Kirchhoff's law for voltages and taking into account the definition of current I = −dQ / dt, find the system of coupled equations of the system and then find the normal angular frequencies of the system.
Driving-point admittance The actual impedance of a load is 30 OHM. The per-unit impedance of the load is 0.5 pu when Base Voltage is 600 V and Base Power is of O 6000 VA O 8000 VA O2000 VA 4000 VA Jump to ncements MacBook Air DD DII F10 F9 F8 000 F7 F6
b) A circuit with an ideal transformer is shown in Figure Q5 (b). The source has an effective value of 100 V rms, and the load is Zz = 400+j400 2. Let N₁ = 100 turns and N₂ = 500 turns, find the average power delivered to the load. N₁ : N₂ 12, R₁ = 102 Figure Q5 (b) V₂ Z₁
Given VRL = 4V and IN = 0.02 A Find Pmax
The equation of two currents in parallel connected in electric devices are i = 12 sin ( 377t + T/4 ) Ampere and i, = 5 sin ( 377t - T/4 ) Ampere. a. What is the ms value of the resultant current? b. What is the value of A and B? c. What is the form factor?

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning