Given data : K=70 MPa Poisson ratio30.22 Find E

Q: Given is a thin-walled tube with the following data: Wall thickness- 2mm ABC is a sector with a…

A:

Q: Determine pressure in [kPa] in the cylindrical pressure vessel shown, if the measured hoop strain is…

A: Given, εhoop=500×10-6E=70 GPa=70×109 Paμ=0.33Ri=400 mm=400×10-3 mmt=6 mm=6×10-3 mm Internal diameter…

Q: Aim: To conduct a full kinematic analysis and calculate dynamic reaction forces in a linkage…

A:

Q: n elliptical hair, 10.0 cm long, has the following semi-diameters A = 35\mu , B=25 \mu When the hair…

A: To calculate the modulus of elasticity, use the formula:Given:Original length of the hair (L) = 10.0…

Q: For the stress-strain curves below, which statements are correct? Stress (MPa) 60 50 40 30 20 10 A B…

A: Given

Q: For the Cobb-Douglas production function Q = AKª L' - a, find the elasticity %3D of substitution by…

A: Partial differentiation are calculated and put into expression to get the value of sigma.

Q: UT FOR CONCENTRIC 回SS, Fy (MPa) 0 5-222 222 32 S 寸 246 288 288 244 287 286 19739 241 284 282 322 074…

A:

Q: the bar element's linear shape, or interpolation ons are: N1= 1-x/L, and N2= x/L (where L is the ent…

A:

Q: During a football game, a vertebra in one of the player's spines experiences a shear force of 524 N.…

A:

Q: Determine the forces acting on the ground and the torque, T12, to maintain static equilibrium for…

A: it is asked to solve the problem both graphically and analytically

Q: Part 2 a) What is the elastic modulus of tempered steel in GPa using the data from VMSE? b) What is…

A: Elastic modulus of a tempered steel is the slope of the virtual material science and engineering…

Q: center. Which property of this rod can be used to estimate how  much the rod should bend at the…

A: The stiffness of a component refers to how it bends under stress while maintaining its original…

Q: Consider the mapping in 2-D only = X1 +7X2 = X1+ uz *2 = (1+e)X2 = X2+ Uz. (1) 1. In terms of y and…

A: As per honor code and answering guidelines I can answer 1st 3 subparts at a time.If you want other…

Q: The table gives data concerning the shrink fit of two cylinders of differing materials and…

A:

Q: how convergence study can be carried out for the problem. (Note: no detailed drawing of mesh is…

A: Finite Element Analysis (FEA):Finite Element Analysis (FEA) is a key component of contemporary…

Q: Data: P = 2 kip d = 3.6 inch w = 305 millimeters t = 0.03 meter r = 5.08 centimeter h = 0.6667 feet…

A:

Q: Q2: Using a power law curve fit, & = Bom, find the value of B and m. Also calculate approximate…

A: The power law curve is

Q: Calculate the stiffness matrix for the Q8 element shown below. Make use of the shape functions in…

A:

Q: Air flows in a pipe under fully developed conditions with an average velocity of 1.25 m/s and a…

A:

Q: Given is a thin-walled tube with the following data: Wall thickness- 3mm Torque is 900 N.m Length of…

A:

Q: Temperature (C 200 100 (Pb) Add your answer a+L 18.3 20 183°C 40 619 60 Composition (wt% Sn) P+L 80…

A: For the solution refer below images.

Q: solid circular steel is tested within the spring range where the following was measured: Load =…

A:

Q: Example 10: An engineering in PVC pipe factory wishes to select a pipe bearing pressure in the…

A:

Q: 9.4 A steel cylinder 1 m long, of 150 mm internal diameter and plate thickness 5 mm, is subjected to…

A:

Q: 7. Frequently the S-N curves for steel can be approximated by a straight line between N = 10 and N =…

A: Graph is plotted on log-log scalefrom the graph the stress(MPa) and the corresponding failure cycles…

Q: Given data : Work done=3800 J Force3D28 N Determine displacement

A:

Q: From the shear stress - shear strain diagram shown below, all the following are true except: Shear…

A: Option d is incorrect.

Q: Given is a thin-walled tube with the following data: Wall thickness- 3mm Torque is 900 N.m Length of…

A: as per our guidelines, i solved the first 4 parts only

Q: I took a flight from Los Angeles to Denver, and I carried with me a closed water bottle of the type…

A:

Q: Table 4 shows the fatigue data of a ductile cast iron to be used for an automobile axle that rotates…

A: a)

Q: Q1 (b) A compression test was carried our by using cylindrical sample made from steel with young…

A:

Q: 1. Determine the driven response for: B₁ k k m₁ m₂ Given: k spring constant, m; - mass, B; - damping…

A: Given : To find : Drive response

Q: Find the diameter of a shaft to tansmit twisting moments varying from 800 N-m to 1600 N-m. The…

A: GIVEN DATA MAXIMUM TORQUE T=1600N-m MINIMUM TORQUE T=800 N-m σut=600MPa σy=450 MPa Kt=1.2…

Q: R10 Reaction Points 84 cm Loading Points Area = 1594 cm^2 W/2 W/2 54 cm L1=27 cm w Figure 2.…

A: given data;

Q: Which of the following parameters should not be selected as repeating variables in using Buckingham…

A: Answer: ◆ The parameters that should not be selected as repeating variables are:  a. Both pressure…

Q: Given data : Work done=30 J Force-5 N Determine displacement

A: Given data : The value of work done W=30 J The value of force F=5 N   To find : Displacement