GIVEN D9N Dozer (Fig. 7.14) Move 2000 LCY Distance - 400 ft. (Fig. 7.14) Grade – 1% uphill (Table 7.2) Material - Loose stockpile (Table 7.2) • Operator Skills – Excellent (Table 7.2) Actual Time Working - 50 min/hr (Efficiency) • Operator Technique - slot dozing (Table 7.2) Visibility – N/A (Table 7.2) Material Weight- 2100 lb/CY (standard weight is 2300. Divide 2300 by material weight to get the factor) Transmission – Direct drive (Table 7.2) Dozer Blade - Straight blade D9N Book Efficiency (Fig. 7.14) X above factors Actual Efficiency Factors: grade x material weight x operator x type material x operator technique x visibility x efficiency x transmission x type blade

GIVEN D9N Dozer (Fig. 7.14) Move 2000 LCY Distance - 400 ft. (Fig. 7.14) Grade – 1% uphill (Table 7.2) Material - Loose stockpile (Table 7.2) • Operator Skills – Excellent (Table 7.2) Actual Time Working - 50 min/hr (Efficiency) • Operator Technique - slot dozing (Table 7.2) Visibility – N/A (Table 7.2) Material Weight- 2100 lb/CY (standard weight is 2300. Divide 2300 by material weight to get the factor) Transmission – Direct drive (Table 7.2) Dozer Blade - Straight blade D9N Book Efficiency (Fig. 7.14) X above factors Actual Efficiency Factors: grade x material weight x operator x type material x operator technique x visibility x efficiency x transmission x type blade

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

NEED ASAP, PLEASE DON'T ROUND-OFF UNLESS FINAL ANSWER
5:26:32 0 200 vo 4G KB/S LTE il (42 expert.chegg.com/expertqna 10 = Chegg Time remaining: 01:58:15 Civil Engineering Determine the viscosity of fluid between shaft f 2- sleeve shown in fiqure below. Assume linear velocity distri bution. 200 mm flaid Aus. : I.183 pa.s V=o.2 89N Const. velaity 7 Sum dia. 0.075mn Submit Skip > |||
I need a quick solution within 15 minutes With my best wishesTon
Q4 Identify the provision relate to safety according to FMA 1967. Structurally sound premises to sustain loads. Handling explosive, inflammable substances. Prevention for the workers to lift, carry or move any heavy load so as to be likely to cause bodily injury to him. Construction, maintenance and safe guard of machineries. I. II. Ш. III. IV. (a) I and II only. (b) I, II and III. (c) II, Ш and IV. (d) I, II, III and IV.
Hand written please
Please, I want a quick solution
The group pile will be developed without onsite static load tests. The soil conditions are consistent, and the site characterization program was Average. A single pile of that group with a circular shape is shown in the figure below. There are 4 rows of 3 piles with center-to-center spacing of 3 meters in the plan. First, calculate the allowable downward load capacity for a single pile and then find the group efficiency and calculate the allowable downward capacity. (use the table for finding skin friction) Silty Sand (SM) kN m³ Y = 17- kN Ysat 20- Well Graded Sand (SW) kN m³ Y = 20- 2.0 1.5 10.5 K -0.6 Depth(m) N60 1 2.5 4 7 9 12 10 20 12 15 22 20 19 16 24 31
Time left 0:1- 20 If the diameter of the catch area for non-recording rain gauge is 203 mm, then the diameter of the inner cylinder is 64.2 mm. (Area of inner cylinder is one tenth the area of catch area) of Select one: True OFalse
An electrostatic precipitator (ESP) is installed to remove dust from the smoke with an efficiency of 95%. The migration velocity of dust particles is 30 cm/s and the smoke flow rate is 50 m³/s. Each collector plate has total area on both sides as 50 m². Which of the following statements is/are correct about the given ESP? A Total plate area required is approximately 500 m². B A total of 10 plates will suffice. C If efficiency is to be increased by 3%, total plate area will have to be increased by 152 m². D If the ESPs are placed in series each having 95% efficiency, then the number of ESPs required to achieve a minimum 99.5% efficiency is 3.
Can i have the solution for this situation.Thank you
I need the carrect answer as soon as possible please
Pwater = 1000 kg/m3 • g = 9.81 m/s? • di=24 mm • d2=16 mm • L=59 cm W=49 cm Results: Page - - prepared by : Assistant Lecturer Mr. Omar M. yousif Northern Technical University Technical college of Engineering / Mosul Engineering Mechanics (ID(second year) einneah titun Time Quctual(Vmin) Ah Qtr Qact. CD h, (m³/s) H 1 60 s 6 cm 1 21 2 60 s 10 m 2 24 3 4 5 Discussion: 1) Calculate theoretical flow rate.