Given an input signal x(1) = 1 - 1 for the interval ( 1, 2) and x(1) = 0 for the rest of the values and an LTI system with impulse response h(t) = & (1+ 1). Calculate the output signal of the system

Q: What is pulse width modulation (PWM) and how is it used in power electronics?

A: Pulse width modulation (PWM) is a technique used in power electronics to control the amount of power…

Q: (b) Another of the blocks in the diagram is labelled sample-and hold. (i) Explain the purpose and…

A: (i) to explain the operation and principle of the sample and hold circuit (ii) the sample period is…

Q: Q2/ What is the advantage of Digital signal processing DSP, and where should be used?

A:

Q: (a) Define sampling and quantization.

A: In this question we will define sampling and quantization....

Q: Solve in digital format please In your words, describe what the signal modulation process consists…

A: Given:  Brief description: In the given question they want to know the process of modulation of low…

Q: How is the analog signal converted to a digital signal? Explain this in a correct sequence,…

A: Analog to digital conversion is a process of conversion analog signal to digital signal. Analog…

Q: Q) The primary sensor is convert - O The input signal to output signal. O The physical quantity to…

A: In this question we need to choose a correct option.

Q: How can the performance of analog-to-digital converters (ADCs) be optimized in mechanical…

A: Analog-to-digital converters are the electronic device that convert continuous analog signals into…

Q: Mention several names of electronic devices that use the pulse signal processor in their work, and…

A: There are many analog and digital electronic devices which are used in digital signal processing…

Q: Express your answers in engineering units with two decimal points of accuracy. 1) Describe the…

A: (a) Purpose of proportional circuit in a PID control system: It compare the feedback value of the…

Q: what is the difference between a sequential circuit and a combinational circuit in Digital Circuit…

A: Need to brief about the sequential and combinational circuit in digital circuit.

Q: The analog waveform is shown with an effective bit rate of 53000 bits per second. If the analog…

A:

Q: What is counter? What is its purpose? Design an asynchronous counter that counts from 0 to 32 ?

A: In this question we will write about counter and it's purposes.. Note:- due to bartleby policy, I am…

Q: What is the effect of instruction CMC? Set CF=1 Clear CF=0 If CF=1 Change to CF=0, and If CF=0…

A:

Q: Design the circuit that displays 35861429 on the seven segment display (just one). Use shift…

A: To design a circuit that displays the number 35861429 on a seven-segment display using shift…

Q: a) List five (5) methods of analogue signal conditioning.

A:

Q: The error detector compares the ....to the and .. .. produces an error signal equal to the…

A: In this question we need to choose a correct option.

Q: The question is, what exactly is digital audio? What does it mean to convert an analogue signal to a…

A: We need to explain about digital audio and analog to digital converter.

Q: equations the sampling method. Then show the effects of aliasing phenomenon. How to Q1: Sampling…

A: Analog to digital converter- A device or a system which convert analog signal into digital signal is…

Q: In a specific multiplexer, 4 select lines are present. Estimate the number of inputs present in the…

A:

Q: What is analogue signal?

A: The analogue signal is continuous in nature and it represents both time and amplitude.

Q: A Figure 5 Y (ii) State one difference between an op amp and a logic gate (iii) Define the term…

A:

Q: Explain what you know about instrumentation amplifier

A: An OPAMP(operational amplifier) is an integrated electronic circuit that is used to amplify weak…

Q: 3.) What is the meaning of the signal-to-noise ratio for a system, and why is it important?

A:

Q: What is the principle of the method for direct digital synthesis (DDS) of analog signals?

A: We need to explain the principle of the method for direct digital synthesis (DDS) of analog signals.

Q: The figure below shows a block diagram for a typical measurement system. Match the blocks below with…

A:

Q: But what precisely is meant by the term "digital audio"? the process through which sound waves that…

A: Digital audio is the  representation of  the sound that is  recorded in, or converted into, the…

Q: [0 5] the signal in the volt range will be quantified. since n=4; a)Calculate what is the number of…

A: We need to calculate number of level , and step size for quantization .

Q: a. Draw the block diagram of a measurement system. b. Mention the function of signal processing…

A: Measurement system is used to measure a quantity and compare that with the standard quantity.

Q: The attenuation in the pass band or stop band is called a. Cutoff Frequency b. Ripple c. Band…

A:

Q: 5- Discuss the effect of changing the number of bits on the recovered analog waveform. 6- Discuss…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: However, what exactly is digital audio? how analog sound waves are converted into digital audio.

A: Digital signal: Any signal that transmits data as a series of discrete numbers is referred to as a…

Q: c) (i) i. Describe the precaution you would take in selecting the sampling interval ii. How may the…

A: (i) Precaution in selecting the sampling interval, The main precaution is that the sampling…

Q: Please describe as simply as possible in detail, what a multiplexer circuit is, how it works. Please…

A:

Q: A quadrature incremental encoder is used to measure the speed and angular position of a servo motor…

A: Electrical machines can be either generator or motors. They can be either Ac machines or DC…

Q: List four or more functions of signal conditioners.

A: Given:  The signal conditioners functions is shown as:

Maximum power transfer theorem

A resistive load will consume maximum power from a network when the load resistance is equal to the resistance of the network as viewed from the open-circuit terminals, with all energy sources removed leaving only the internal resistances. Physicist Moritz von Jacobi introduced the maximum power transfer theorem in 1940. Therefore, this theorem is also known as Jacobi's law.