Given a effective delay of 20ms when network usage is 38%, what is the effective delay when network usage = 29% ? (Give answer is miliseconds, rounded to one decimal place, without units. So for an answer of 0.10423 seconds you would enter "104.2" without the quotes).

Given a effective delay of 20ms when network usage is 38%, what is the effective delay when network usage = 29% ? (Give answer is miliseconds, rounded to one decimal place, without units. So for an answer of 0.10423 seconds you would enter "104.2" without the quotes).

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Given are the following codewords for an error control coding scheme data 000 011 100 codeword 00011000 00000111 10101000 . a.What is the minimum Hamming distance? b. What is the coding rate for this scheme? c. what raw data rate would be required if we need a throughput of 6 Mpbs? d. in a different situation, the number of data bits to transfer is 5, and the minimum hamming distance is dmin=5. find the maximum coding rate for this situation
A large population ALOHA user manages to generate 50 request/sec, including both originals and retransmissions. Time is slotted in units of 40 ms:a. What is the chance of success at the first time?b. What is the probability of exactly k collisions and then a success?c. What is the expected number of transmissions attempts needed?
We have a 1000 m long 10 Mbps communication channel with ARQ protocol. The signal travels at a speed of 2 ∗ 10 ^ 8 ? / ?Assume that no frame is lost or damaged. Confirmation frames, control information are negligible in size.For what range of frame sizes do we get an efficiency of at least 70%?
I need the answer as soon as possible
As another example, consider a circuit-switched network that connects computers in two remote offices of a private company. The offices are connected using a T-1 line leased from a communication service provider. There are two 4 × 8 (4 inputs and 8 outputs) switches in this network. For each switch, four output ports are folded into the input ports to allow communication between computers in the same office. Four other output ports allow communication between the two offices. Figure shows the situation
A TCP message of 19.2KBytes is sent in a network system with a 1000Byte MTU. Source and destination are 7 hops apart. The distance between hops is 250 km. Each router has a processing delay of 1000nSec (nano seconds). The throughput in the network is 10Gbps except for the device in the last hop which only has a throughput of 5Gbs. Find the end-to-end latency in the system considering this is a Packet Switched network. Consider each packet has 40Bytes of header overhead. The speed and light for this problem will be 200,000 km/s.
Give unique answer only. Do not use AI or plagiarized answer.
A telephone modem is used to connect a personal computer to a host computer. The speed of the modem is 56 kbps, the one-way propagation delay is 100 ms, the packet size is 256 bytes, and the probability of an error in a packet is 10^-4. Find the efficiency of stop-and-wait ARQ. What window size N is needed to keep the channel busy when there are no transmission errors. For this window size finds the efficiency of the go-back-N and selective repeat protocols. Note: Correct and detailed answer will be Upvoted else downvoted
If a two port bridge was used in a heavy load standard Ethernet network such that the traffic is going through it. If each station is theoretically given a capacity of5Mbpsand the number of stations in each LAN segment is equal, then the number of stations in each LAN is:
Unless specified otherwise, use the free space propagation speed of light 3x108 m/s to calculate the propagation delay. For numerical calculations, the results must show the appropriate unit. Show a complete solution for each problem3. Consider a digital multimedia transmission system. Separate audio and video coders are used to encode these signals. Audio and video bits are packed in packets together and transmitted over a transmission link. Each packet is 2,000 bytes long, which includes a 48-byte header. The system generates one packet every 40 ms. Calculate the following values:a. The minimum data transmission rate required to support the above system.b. The minimum signal-to-noise ratio (SNR) in dB required to transmit the above audio and video information. Assume a 400-kHz transmission channel bandwidth is used.c. The end-to-end packet delay over a 50-km link, using answer in Part a).
b) Let's say a networking company uses a compression technique to encode the message before transmitting over the network. Suppose the message contains 6 unique characters of your name and their frequencies are similar to the last 6 non-zero digits of your mobile number. For example, your name is Badhon and the last 6 digits of your mobile number is 123456. So the frequency Frequency (in thousands) Characters B table of characters will be: 2 3 H. 4 Now, if the compression technique used is Huffman Coding instead of variable-length coding, how many bits will be saved in the message? Show the saving percentage. 6.
IN PYTHON Given the following six-node wide area network for which the numbers attached to the links are a measure of the “delay” in using that link (e.g., some lines could be more heavily used than others and therefore have a longer wait time), answer the following question. What is the shortest path from node A to node D, where shortest path is defined as the path with the smallest sum of the delays on each individual link? Explain exactly how you went about finding that path.