Given: A ball of moss I kg is released from rest at A. and rolls down a quarter cirole .until point B. The ball leaves po'int B mith a horizartal velocity vB and undergoes projectile motion; At pairnt c the player hits' the ball with å force of 1000 N,45° above +he harizantal and the point of impoot lasts t = 0.005 Secands. Tmoring air resistance and assuming the work done by friction from A to B is -20 J. Find:0) wock dane by gravity on bal b) Net work done by all farces on the boll from A-B C) VB DI velocity at C E) Mitial /final linear mamentm F) Time it taKes ball to reach player 6) time it takes boll to reach grond after C. 5m B Point of impact t=0.005 isec)

Q: A space truss is subjected to a load of F = {110i – 460k} lb (Figure 1) Three ball-and-socket joints…

A:

Q: 80mm 60mm Vax's Gomm 40mm Find the location of the Controid. Show All work. 1

A:

Q: Q4 The L2 steel bolt as shown in Figure Q4 has a diameter of 5 mm, and the link AB which is made…

A:

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: Chains are used in gears applications while belts are used with pulley systems. Select one: O True O…

A:

Q: What is Ix

A: According to the given data, we need to find a moment of inertia about the X-axis.

Q: Use the graphical method to break F into components parallel to bars AB and BC. If the component…

A: According to the given data  FAB =7kN a = 300mm b = 75mm c = 100mm  we need to find Force in the…

Q: What is the moment-area method?

A: The moment-area method is one of the methods for determining the slope and deflection generated in a…

Q: In the moment calculation, why did you take away the h* from 8?

A:

Q: 5.3' 4.5' 3' 3.5' 4.5' 5.3' 1' 6.8' 3.6' 5.5'

A: Draw a kinematic diagram of given mechanism.Identifying all joints and links also find DOF.

Q: R M P

A: given; lets take tension force in member NJ=T1lets take tension force in member NM=T2lets take angle…

Q: JC BRA JC Ma = 2.5kg BRD BAD Mb=7kg Given that: The line of force for BRD is 5cm. Distance JC to Ma…

A: Mass, Ma= 2.5 kg Distance between JC and Ma, a= 16 cm Mass,Mb= 7 kg Distance between JC and Mb, b=…

Q: Find GG, and all reactions, 20 20k 2ok 20' 10' 10'

A: Given: The structure is  shown below:

Q: How do I find T, P, and x_2?

A: Given data:Heat received by the water = Since tank is rigid, hence volume of tank remains constant…

Q: A Bys Find the reactions. Fill in the blank's. 8k a 4' 6' 6. FBD

A:

Q: How can we find the location of the neutral axis?

A: When a bending moment is applied on a beam, normal stresses are set up in its cross-section due to…

Q: So, what is the magnitud and direction from E to D. ?

A: FBE=0 FAE=288.675 lb (Compressive)

Q: 42 in 64 [in]- 50 in D 59 in 63 in +10 in ... 21 in SAR (

A: Given,

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.