Given: A 450-mm diameter concrete column is to be reinforced with 8-28 mm diameter vertical bars and mm diameter spiral. If fc= 28 MPa and fy = 415 MPa, calculate the following a) The maximum nominal axial strength of the RC column. b) The design axial strength of the column. c) The minimum spiral ratio required for the column section. d) The recommended pitch of the spiral reinforcements.

Given: A 450-mm diameter concrete column is to be reinforced with 8-28 mm diameter vertical bars and mm diameter spiral. If fc= 28 MPa and fy = 415 MPa, calculate the following a) The maximum nominal axial strength of the RC column. b) The design axial strength of the column. c) The minimum spiral ratio required for the column section. d) The recommended pitch of the spiral reinforcements.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Column AB is made from high strength pre-cast concrete and reinforced with four in. diameter A-36 steel rods. The allowable normal stress for the high strength concrete and the steel are (allow)con = 2.4 ksi and (allow)st = 24 ksi, respectively. The modulus of elasticity for high strength concrete is 4.2 × 10³ ksi and for A-36 steel is 29 x 10³ ksi. (Figure 1) Figure 10 ft 9 in. H 9 in. Section a-a Part A Determine the magnitude of the maximum allowable floor loading P. Express your answer to three significant figures and include the appropriate units. Pmax = Submit 04 μA Provide Feedback Value Request Answer Units ?
Design the simply supported beam shown in the Figure 1 for flexure Consider the following data. Characteristic compressive strength of concrete, fck= 25 N/mm? %3D Characteristic tensile strength of steel, fyk = 500 N/mm? Effective cover to reinforcement is 30 mm Density of Block work = 20 kN/m3 Draw the cross section of the beam at the mid span Height of 200 mm thick wall above the beam is 4 m 200 mm - Imposed Load-20kN/m 600 mm - 6 m
Problem Solving: A rectangular beam has dimensions of 250 mm by 625 mm with an effective depth (distance from extreme fiber in tension to the centroid of the reinforcing bars) of 575 mm and is reinforced with three 25 mmp. The concrete cylinder strength f.' = 27.6 MPa and the tensile strength in bending (modulus of rupture) is 3.28 MPa. The yield point of the steel is 414.7 MPa. The beam carries a bending moment of 61 kN.m. E_ = 200000 MPa. E_ = 4700,f. Using the transformed area method, determine the stress in the extreme fiber in compression.
rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 420 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. Determine the maximum steel area for a tension controlled singly reinforced condition in positive bending
Design Problem 1 & 2 Determine the cracking moment for the prestressed beam section shown if f'c = 35 MPa. Use a modular rupture of fr Assume normal weight concrete. = 0.621√ f'c C = 100 mm b₁ = 350 mm D = 125 mm d = 440 mm h = 500mm b₂ = 200 mm Figure 1.0 Cc 60 mm C-150 mm h, 250 mm b₁ = 250 mm b. =350 mm Figure 2.0 d 630 mm h = 700mm Ce 70 mm
Please give me the correct solutions and answer of this problem in principles of reinforced/prestressed concrete
Considering the nominal shear stress on concrete is f = 0.83 MPa. Calculate the allowable max spacing for 2-legged 10 mm stirrups? Use simplified calculation for Vc. Beam dimensions are 397 x 754 mm. Effective cover of steel reinforcement = 70 mm fy = 275 MPa Spacing should be in multiples of 10 mm. NOTE: USE STORED VALUES IN YOUR CALCULATION
Given the following properties of beam: b = 250 mm, d = 325 mm and h = 400 mm. a) Assuming the concrete is uncracked, compute the bending stresses (in MPa) in the extreme fibers of the beam at M = 100 kN-m. Blank 1 b) Determine the cracking moment (in kNm) for the section if f'c = 28 MPa. Blank 2 c) Compute the flexural stresses in the concrete and steel of the beam using the transformed-area method at M = 100 kN-m, n = 9 and reinforced with 5-16 mm diameter tension bars. Unit must be in MPa. fc = _Blank 3, fs =__________ Blank 4
Find the ultimate moment of resistance for the rectangular section reinforced as shown below. material strengths: Concrete Reinforcement Width of section Reinforcement fcu= 30-MPa fy:= 450-MPa b:= 280 mm d:= 510 mm d':= 50-mm 2 A, 2410-mm A's:= 628-mm 2 b A', Hi As
pls help me.
A rectangular beam with width of 233 mm and overall height of 431 mm is prestressed by using a bonded (stress relieved) tendons with a specified tensile strength of prestressing tendons fpu %3D 1380 MPa. Strength of concrete is 33.1 MPa. The area of presstressed reinforcement in tension zone is 1,024 mm2 and its centroid is located 40 mm above the bottom end of the beam. The specific yield strength of prestressing tendons fpy = 1220 MPa. Compute for the ultimate moment capacity of the beam.
I need the answer quickly