Give the value of the IP, auxiliary flag, zero flag, the carry flag, the sign flag, the overflow flag, and the parity flag after each of the following instructions if AX is initialized with 0x1325 and BX is initialized with 0x0EEE. Using NASM Simulator (DOSBox)   add ax, 0xFCDA add ax, bx add bx, 0xC002

Q: Please give me the answer with step by step solution Qns:CONVERT THE FOLLOWING TO MIPS CODE

A: To convert the given code to MIPS assembly code, we will use the following register names: $s0 for…

Q: The MC68000 standard specifies which forms of destination name addressing are forbidden and why.

A: When someone claim they built their own computer, they mean they took an off-the-shelf CPU, plugged…

Q: A system using segmentation provides the segment below. Compute of the logical addresses. If the…

A: a. 0, 323 Segment = 0 Offset = 323 Offset < Length (323<400) Physical Address = Base + Offset…

Q: Check if the code word is correct, assuming they were created using an even parity Hamming Code. If…

A: Answer:

Q: In a basic MIPS datapath, how does the ALU perform a NOT operation? What are the resulting LF bits?

A: MIРS-Dаtараth  is  а  grарhiсаl  MIРS  СРU  simulаtоr.  The  рrоgrаm  is  intended  tо  be  used  аs…

Q: In MIPS architecture, a pop causes $sp to:

A: $sp it is a stack pointer which is a general purpose register.  Stack  pointer always point to the…

Q: Write an ALP for the following scenario: Get an 8 bit data "X" from port PO and another 8 bit data…

A: Answer: here we will understand how much data will take for perform this operation. Given X-8 Bit…

Q: In a datagram network, two columns are required; in a virtual-circuit network, four columns are…

A: Given: A datagram network must have at least two columns; a virtual-circuit network must have at…

Q: Suppose two users in a Direct Sequence-CDMA system have signatures (that is, sequences of chips)…

A: Actually, given question regarding CDMA.

Q: Please answer question C draw the circuit diagram. otherwise will downvote. Suppose there is a 4…

A:

Q: Interface 8254 with 8086 at counter 0 addresses 7430H. Write an ALP to call subroutine after 100 ms.…

A: Given: Interface 8254 with 8086 at counter 0 addresses 7430H. Write an ALP to call subroutine after…

Q: If EBX=81264831 CX=5622 , what is the value of Ch after execute Mov CX, PTR EBX Select one: a. 56 b.…

A: CX can be divided into 2 parts. They are CL and CH. The initial 2 numbers will be stored in CL and…

Q: Problem Five Consider a serial port operating with a baud rate of 10,000 bits per second. Draw the…

A: I will explain this question draw the help of figure.

Q: This article describes interruption latency and context transition time.

A: Concepts of interruption latency and context transition time.

Q: Transmitted messages often include a parity bit whose value is combined with a data byte toproduce…

A: Determine the parity of the given message byte: To determine the parity of the given message byte,…

Q: Question 2 Select ALL the operand specifiers that correctly produce an effective address of 0x114.…

A: - We need to talk about the addresses here whoch produces 0x114.

Q: Write an AVR C program to read the content of location OX005F of EEPROM into PORTB. Solution:…

A: Given,

Q: The address field of a Frame Relay frame is 1011000000010111. What is the DLCI in decimal? What is…

A: Dear student, As per guidelines, I can do only first 3 subparts. Please re-post your pending…

Q: Calculate the values of the pins A0 and BHE’ and how many bus cycles are required for completing the…

A: Answer: I have given answered in the handwritten format in brief explanation.

Q: Given the following memory blocks with their internal decoders: 4 K words, 2 K words, IK words, 1 K…

A: Answer: Given blocks are 4K words, ak words, Ik words & 1k words. UK words block has has 12…

Q: Write an 8051 asm program to send a welcome message "Warm Welcome" serially. Whenever the INT1 has a…

A: Solution:- To implement 8051 asm program for displaying the message , "Warm Welcome".   Note: I have…

Q: 3. Find the time delay for the delay subroutine shown as follow, if the system has an S051 with…

A: The CPU takes a particular number of clock cycles to perform an instruction. These clock cycles are…

Q: IV Figure below shows a multiplexer in a synchronous TDM system. Each output slot is only 10 bits…

A:

Q: nterface 8254 with 8086 at counter 0 addresses 7430H. Write an ALP to call subroutine after100 ms.…

A: Summary:In this question, we need to write an ALP to call the subroutine after 100ms

Q: Design a datapath to solve the following equation: K is the input P=(1+ 102/128) K + 32 Define how…

A: To design a datapath to solve the given equation, we need to break it down into individual…

Q: Write a C program for the ATmega328PB that continuously toggles bits 1, 3 and 6 of Port B every 250…

A: it continuously toggles bits 1, 3 and 6 of Port B every 250 ms

Q: Write a C program to toggle only bit 4 of Port C every 200 ms For the toolbar, press ALT+F10 (PC) or…

A: Toggle the port C  For every 200 micro seconds Only 4 bits.

Q: ind the 32-bit representation for the following command, and then discuss which bits of this 32 bits…

A: Solution: The instruction is add r5,r6,#11. The first three bits are Condition bits, Operation Code…

Q: Find the value of divisor latch values to set UART baud rate to 9600bps in LPC2148 for given PCLK =…

A: Here we find the divisor (MSB AND LSB):

Q: 28 A paging scheme uses a TLB. A TLB access takes 10ns and main memory access takes 50ns. What is…

A: The correct answer is  65

Q: The lowest address decoded by the following circuit is A14 A0 D A15 0101 1000 0000 0000 0000 010…

A: A logical circuit is an electronic circuit that performs a logical operation on one or more binary…

Q: After initializing 8259A with port addresses CO H and Cl H for Ao = 0 and Ao = 1 respectively. Give…

A: Requirements :-

Q: A switch is connected to pin PORTB.7. Write a CIS program to monitor S W and create the following…

A: Answer is given below-

Q: On a bus topology, terminators eliminate the possibility of EMI Crosstalk Noise Signal bounce ▸

A: A bus topology is a network configuration in which all devices are connected to a common…

Types Of Protocols

A network protocol is a collection of rules that governs the exchange of data between devices connected to the same network. In other words, network protocols are rules that specify how devices communicate or transfer data over a network. The sender and receiver systems must obey the standards to facilitate communication between them.