How would you solve this Give the location dimensions to the three (3) Ø.437±.005 holes from CGive the location dimensions to the three (3) Ø.437±.005 holes from BGive the location dimensions to the two (2) Ø.187±.003 holes from A 6:25 PM Sat Oct 107e 100%BRACKET- ---.A.53.622X R.122X 1.2004X 0.156±.005A 9.010 O A DO B0.002 MA-4X 0.187+.0030.028 (M| A|BC009 XZ3X 0.437+.005O 0.014M ABC+ 0.002 M AB009'E000'S0002'70008'0006009374000S'I4.05003740.875±.005-O 0.0280 ABC-000SCALE:1 = 1APPD:CDATE:DR:REV:NrWUNLESS OTHERWISE SPECIFIEDINCHESAND TOLERANCES FOR:SAFETYMARINE1 PLACE DIMS.;1724 Marine DriveMinneapolis, Minnesota2 PLACE DIMS.;LO3 PLACE DIMS.;NAME:BRACKETNOTES:ANGULAR;FRACTIONAL;REMOVE ALL BURRS AND SHARP EDGES.2. DIMENSIONING AND TOLERANCING PER ASME Y14.5-2009.* 1/32FINISH: MIL-C-5541-CLIA PART NO:FIRST USED: SIMILAR TO:MATERIAL:6061-T6AL ALY. .093 THICK

In the given figure, here the datum A, datum B, and datum C make the primary datum reference plane.…

Give the location dimensions to the three (3) Ø.437±.005 holes from C Give the location dimensions to the three (3) Ø.437±.005 holes from B Give the location dimensions to the two (2) Ø.187±.003 holes from A

Give the location dimensions to the three (3) Ø.437±.005 holes from C Give the location dimensions to the three (3) Ø.437±.005 holes from B Give the location dimensions to the two (2) Ø.187±.003 holes from A

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Sketch the 2D figure of cover using AutoCAD and mention all the dimensions, colour the hatched lines if there any. 80 Dia 8 42 106 22 42 16 24 R 16 R 80 Cover
Draft and annotate the 2D sketch of cover using AutoCAD and mention all the dimensions. Colour the hatched lines which are inside the curve 8R 6 holes 8 Dia 62 Dia 18 R 3 holes 20 Dia 110 Cover 40 Dia 100 R
Draw the three projections of the body in Figure 1- using AutoCAD 1-Do not write the dimensions on the drawing 2- Draw with the same measurements as shown 3 -Show graphics properties At least properties are required for the circle and arc R10 R20 40 35 55 -1- JSI 9.
Draw, using 1 st angle projection Orthographic view of the following figure with suitable scale, the following views: (a) the given front elevation; (b) a top view (c) side elevation (d) an isometric view of the block. Show all hidden details. Print scale and show six leading dimensions Note : use creo PARAMETRIC to figure out
Draft and annotate the 2D sketch of upright using AutoCAD and mention all the dimensions. Colour the hatched lines (blue) which are inside the curve 54 22R 3 holes 14Dia 13R 16R 27R 15 80 Upright 9R 65 120
3
do not reject . let other do the solution if u dont know. skip 86 30 ugh hole 16 6 20 Dig 28 18 Dia for the above isometric view , sketch the orthographic view in first angle proiection using catia v5 software. 36
Basics in engineering drawing
AutoCAD Sketching The given sketch is a cross section view of housing. Sketch the 2D sketch of the below figure using AutoCAD. Note: color the hatching if there any and mention the dimensions and reference lines 58 8 holes 10 Dia 40 Dia 15R 16 20R 58 Dia 20R 6 holes 8la 40 40 Housing 22
The given sketch is a cross section view of bracket. Sketch the 2D sketch of the below figure using AutoCAD. Note: color the hatching if there any and mention the dimensions and reference lines 36 4 holes 10Dia 12R 15R 20 32R 26 lia 32 R 65 Bracket 100
Determine the following based on the given: a) velocity of point A (in/s), b) the angle of Va with reference with the x axis, c) component of Va perpendicular to line AB, d) angular velocity of link 4 (rad/s), e) velocity of point B (in/s), and f) the angle of Vb with reference to x axis.
Figure out the 2D sketch of bracket using AutoCAD and mention all the dimensions. Colour the hatched lines which are inside the curve 2 holes 22 Dia 46 100R 16 [15R 6 holes 10 Dia 18 R Bracket 09 62 Dia 09 80 Dia