Give 5 Differences Between Artistic and Engineering Drawing.

Q: Explain what basic drawing conventions are used and why there needs to be different types of…

A:

Q: Explain the difference between 1:50 and 1:100 in scale ruler Sketch it please to fully understand…

A: In architecture and civil drawings, different scale measurements are used in order to transfer the…

Q: From the open compass traverse shown, if the forward bearing of line AB is N 75°30' E, compute the:…

A:

Q: What is the importance of scaling the drawing to different paper size

A: Explanation:  Scaling in engineering drawings is very important aspect of any kind of drawing. To…

Q: tant is lettering in the technical drawin

A: Lettering is the process of forming letters, numerals, and other characters in technical drawing. It…

Q: What is the relationship between the drawing and specification/

A:

Q: typeface

A: A typeface is the design of letters in writing that can include different variations in width (e.g.…

Q: 2.5 m 750 N·m k 2.5 m 기 1200 N·m

A:

Q: A U-tube differential manometer connects two pressure tubes A and B. Pipe A contains carbon…

A: 1. Pressure in Pipe A () = 120 kPa2. Specific gravity of carbon tetrachloride in Pipe A () = 1.63.…

Q: why does the field of engineering need standardization in technical drawing?

A: Standardization in technical drawings mean ensuring and fixing certain parameters in drawings to…

Q: Given lines AB, BC, and CD, a reversed curve is to connect these three lines thus forming the…

A:

Q: 1. The radius of a simple curve is twice its tangent distance, if the degree of curve is 4°. a) What…

A: This problem is related to Simple Curve from Surveying Engineering. In this question, Given a simpe…

Q: Problem 6: Determine the maximum torque that can be applied to a hollow circular steel shaft of…

A: Outside diameter of shaft, Do=100mmInside diameter of shaft, Di=80mmMaximum shear stress,…

Q: The angle between a 5-m full station of a certain curve is 10°. The curve has 7 intermediate…

A: Some points to be considered 1) Point of curvature 2) Point of tangency 3) Length of the Curve   The…

Q: Write the types of structures in detail.

A: The type of structure to be constructed for a purpose depends upon the use of structure, load on…

Q: can you put an illustration?

A: Data Available: Shape of the tank = Cylindrical Diamter of the tank = 1.5 mHeight of the oriface =…

Q: A woman stands on a weighing scale while riding in an elevator. When the elevator is at rest, the…

A: Given: The mass of the woman is 125 lbs. The acceleration is 4 ft/sec2.

Q: (a) Describe the purpose of detail design in your own words.

A: Detail design: Detail design involves the complte design procedure. The design procedure of every…

Q: 2. Two points, A and B, are established along the same direction from a theodolite station. If the…

A:

Q: Identify the several types of lines used in drawing and explain their uses

A: To list different types of lines used in engineering drawing

Q: List the only tools needed for producing FREEHAND sketches

A: The only tools needed for producing FREEHAND sketches are listed in the following steps.

Q: Draw Shear force (SFD) and Bending moment diagrams (BMD) of the following beam.

A:

Q: 9-7. Determine the reactions at the supports A, B, and C, then draw the shear and moment diagrams.…

A:

Q: Significance of architectural lettering in technical drawing and engineering drawing?

A: Just like architectural drawings, hand lettering should be clear and legible. Even with digital…

Q: 2. A compound curve has the following data: I1 = 28°, 2 = 31°, Di = 3°, D2 = 4°; Find the stationing…

A: I1 = 28°I2 = 31°D1 = 3°D2 =4°Station of PI = 30+120.50

Q: How are the following line types used on orthographic views of engineering drawing? Short break…

A: Solution:- The following line types used in engineering drawing is shown below, 1) Shorty break line…

Q: i. Select any four (4) favorite AUTOCAD COMMANDS and explain when and how to apply them. ii.…

A: CAD, or computer-aided design and drafting (CADD), is a design and technical documentation…

Q: 2. An unsymmetrical parabolic curve has a forward tangent of -8% and back tangent of +5%. The length…

A:

Q: Define drawing paper with sizes.

A: The most common paper sizes for drawing  are A0, A1, A2, A3, A4, A5.   The table below shows the…

Q: etermine the minimum sight dista two-lane divided Highway in hilly na 4% descending grade. data as…

A:

Q: Where can we find the most common application of technical drawings?

A: Technical drawings represent the exact shape, dimensions and composition of an object with a view to…

Q: Detail drawing is a multiview representation of a single part with dimensions and notes. Select one:…

A: Detail drawing conveys the information and instructions for manufacturing the part. Hence Detail…

Q: system consists of 60lb and 20 lb blocks A and B, respectively, and 5-lb pulleys C and be treated as…

A: ma=60lb mb=20lb