Geometric Characteristic Symbols. Tolerances of: ______________________ ______________________ ______________________ ______________________ ______________________ State the five (5) types a) b) c) d) e) a) linear b) linear and angular c) linear, angular, and fractional d) square and rectangular

Q: Determine the Young's modulus of a metal alloy having the following tensile stress-strain diagram.…

A: As From the Figure the Stress-Strain curve  is linear Form As we know the  Slope (E)=StressStrain…

Q: Determine the x-, y-, and z-coordinates of the mass center of the body constructed of three pieces…

A: Center of mass: The Center of mass is the point on a body about which it is assumed that the total…

Q: A projectile is launched from point A with the initial conditions shown in the figure. Determine the…

A:

Q: In the figure below, explain the case where the dimension tolerance is satisfied, but the plane…

A:

Q: The degree of precision of a quadrature formula whose error term is : O 4 2

A: Givenerror term is h23f3ξ

Q: State the five (5) types of Geometric Characteristic Symbols. They are tolerances of: (Enter your…

A: Geometric dimensioning and tolerances is a subject which deals with the quality of a fabricated…

Q: On the part below, with only the limits of size specified, what coaxiality tolerance is implied…

A: In this problem, it is asking about the co-axially tolerance between the two diameters.

Q: The rectangular coordinates of a particle which moves with curvilinear motion are given by x =…

A: Givenx=10.25t+1.00t2-0.25t3y=6.10+16.04t-2.29t2t=4sθ=28o

Q: Given the following duty record, how much life is consumed at each stress level? 60 ksi 49 ksi 10…

A: An S-N curve establishes the number of cycles required to cause failure when a material is…

Q: Which position tolerance is shown in below’s technical drawing? Explain the meaning (that is the…

A: Which position tolerance is shown in below technical drawing?Explain the meaning (that is the…

Q: Primary Creep: slope (creep rate) decreases with time Select one: True False

A:

Q: Based on the picture below, calculate the calibration. Include proper units. 20 20 30 10 5, 1.0 20…

A: Given: Calculate the calibration, in proper unit.

Q: The provided S-N curve shows the fatigue strength of a ferrous component with unknown geometry.…

A: When a material is regularly cycled across a specified stress range, the number of cycles before…

Q: Select the most appropriate answer from the multiple choices given (5 marks for each one). I- A…

A: 1. Time constant is given by    =2501000   =0.25secoption d is the correct answer.

Q: Hole-MMC_ LMC_ LMC Shaft-MMC_ LMC_

A:

Q: Errors due to manufacturing defects in the instrument is called as Aging Error. Select one: O True O…

A: Errors due to manufacturing defects in the instrument is called Systematic Errors.

Q: I require a gap of .03 min and .06 max between the 2.50 dim and the B dim (at the bottom). I apply a…

A:

Q: Determine the x- and y-coordinates of the trapezoidal shape. y 2.8 b b 1.7 b 1 x

A: GIVEN DATA- A COMPOSITE SHAPE IS GIVEN WE HAVE TO FIND COORDINATE OF CENTROID OF FIGURE

Q: A material condition used to indicate that a specified geometric tolerance applies at each increment…

A:

Q: 1. Plot the stress'strain diagram for the material. 1. Use the graph to calculate:

A:

Q: Which variant of defining dimensions (A or B) would allow a higher overall part length tolerance, if…

A:

Q: In the figure, one end of a uniform beam of weight 340 N is hinged to a wall; the other end is…

A:

Q: Problem (7): Determine tolerance value and limit dimension of the rod which a diameter is ∅25 mm,…

A:

Q: You have a 81.4% efficient pulley system arranged such that the effort pulls upward. Suppose that…

A: VR=distance moved by effortdistance moved by load=14.63.65=4& η=MAVR×100%81.4=MA4×100%MA=3.256

Q: R1 ww 11) Consider the following circuit. An ammeter with internal resistance Ri is inserted between…

A: Step 1:Step 2:Step 3:Step 4:   Verification for part (a) using simulatorVerification of part (b)…

Q: What are the geometry features in the picture below? Indicate main geometry and tolerances

A: Geometry Features which mentioned in the Drawing are as below:

Q: On the drawing attached, before any geometric controls are applied, what is the coaxility tolerance…

A: The tolerance for how near one cylinder's axis is to another is known as coaxiality. A shaft with…

Q: Determine tolerance value and limit dimension of the rod which a diameter is ∅6 mm, according to the…

A: Given Data Nominal diameter of rod is : d=6 mm Upper deviation is : es=-40.64 mkm=-0.04064 Lower…

Q: C. C. H. Time Vol C. m'jsec. 10 mjsec. 10 المعل من المنحني المعل من القراءات m*10 m10 No sec. 0.074…

A: Given data

Q: On the left end of this object, the thread note indicates 10UNC. What is the pitch for this thread?

A: The objective of the question is to determine the pitch of the thread indicated as 10UNC on the…

Q: Given a hole with a size dimension of Ø.875±.003 and a positional tolerance of.002 at MMC, what is…

A:

Q: Q/drow the isometric .8, 80 20 20 20 40 10, 09

A:

Q: The provided S-N curve shows the fatigue strength of a ferrous component with unknown geometry.…

A: When a material is regularly cycled across a specific stress range, an S-N curve determines the…

Limits, Fits, and Tolerances

The maximum or minimum allowable sizes within which the size of component lies are known as limits. The limits are classified into two types: