GA manometer is made of a tube of uniform bore of 0.5 cm2 cross-sectional area, with one limb vertical and the other limb inclined at 30° to the horizontal. Both of its limbs are open to atmosphere and, initially, it is partly filled with a manometer liquid of specific gravity 1.25. If then an additional volume of 7.5 cm3 of water is poured in the inclined tube, what is the rise of the meniscus in the vertical tube? (а) 4 cm (b) 7.5 cm (c) 12 cm (d) 15 cm

GA manometer is made of a tube of uniform bore of 0.5 cm2 cross-sectional area, with one limb vertical and the other limb inclined at 30° to the horizontal. Both of its limbs are open to atmosphere and, initially, it is partly filled with a manometer liquid of specific gravity 1.25. If then an additional volume of 7.5 cm3 of water is poured in the inclined tube, what is the rise of the meniscus in the vertical tube? (а) 4 cm (b) 7.5 cm (c) 12 cm (d) 15 cm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A manometer is installed in a vertical pipeline. Determine the difference in pressure in PSI between point A and point B if the gauge liquid has a specific gravity of 1.50 and shows a deflection of 80cm.
4. A 1.9-mm-diameter tube is inserted into an unknown liquid whose density is 960 kg/m3, and it is observed that the liquid rises 5 mm in the tube, making a contact angle of 15°. Determine the surface tension of the liquid. WindowC
Please correct solution
Rush, help me solve this one
You want to measure velocity in a water tunnel. Due to budgetary restrictions, you were unable afford a pitot-static tube, so you decided to inserts a total-head probe and a static-head probe both in the mainstream away from the wall boundary layers. The two probes are connected to a manometer. Write an expression for tunnel velocity V in terms of the parameters in the figure. Is it critical that the first head be measured accurately? And how does part this differ from a Pitot - static tube formula?
A figure shows a differential manometer connected at 2 points A and B. At A pressure pressure is 100 kn/m^2. Find the absolute at B A 650mm water 250mm 150mm TATT out of sp gravity = 0-85 B Hy (Sp.gr = 13-6) Pilipita menge k
A pipe carries an oil of specific gravity 0.8 with pressure 19.62 kPa. The pipe is 3.5 m above datum level. What is piezometric head in meters?
a pipe has a pressure of 4000 pascal and is connected to a 36 degree inclined single column manometer. the level of mercury in the reservoir is at a height 20 cm below the center of the pipe. The length of the inclined column which is at the same level from the mercury inside the reservoir up to the end of the column at the reight limb is 25 cm. Find the specific gravity of the fluid inside the pipe. The area of the reservoir is 125 times the area of the right limb of the manometer
A sight is taken with an Engineer's Level at rod held 200 meters away and an initial reading of 2.3 meters is observed. The bubble is then level through 7 spaces on the level tube, and the rod reading is 1.8 meters. One division in the level tube is equal to 0.6 mm. What is the sensitivity of the level tube in meters? What is the radius of curvature of the level tube in degrees?
I need the answer as soon as possible
U-tube manometer is connected to a conical vessel as shown in figure. Manometer shows a reading of 8cm when the vessel is empty. What will be the reading on the manometer when the vessel is filled with water? Note: Right limb contains water before and after the vessel is filled. 0.08 m 11m1 /1.75m
An open, clean glass tube is inserted vertically into a pan of water. What tube diameter is needed if the water level in the tube is to rise one tube diameter (due to surface tension)? The contact angle is 0 and ss = 0.073 N/m