fur a Purely Inductive Inductive circult the power is given by p= -1/2 VM IMSin (2wt) It the current is given by i = Imsin (wt-II ) V= VM Sin (wt) Prove that this is correct.

Q: Describe the cutoff condition in a BJT circuit?

A: The cutoff mode is the opposite of saturation. A transistor in cutoff mode is off, there is no…

Q: An ideal air-core solenoid has a length of 6.5 cm, area of 2 cm² and 3000 turns. Find the self-…

A: Given data as per question L  = 6.5cm A =  2cm2 N =3000

Q: A Coiled telephone cord forms a spiral with 51-0 tumsa diameter of 1.30cm, and an unstretched length…

A: Given that For a spiral telephone cord the number of turns is N=51 diameter of the cord is d=1.3cm…

Q: A solenoid of radius 2.30 cm has 560 turns and a length of 15.0 cm. (a) Find its inductance. mH (b)…

A: to be given questionradius r=2.30 cmturn N=560 turnlength l=0.15 memf = 70 mV

Q: A 1.35 H inductor in an RL circuit (with resistance 2.25 ) is initially carrying a current of 5.1 A.…

A:

Q: The current in an RL circuit builds up to one-third of its steady-state value in 5.54 s. Find the…

A:

Q: half O A tectangular conducting loop has its left in a magnetic field directed into the page. S…

A: when we increase the magnetic field in the page so Loop pused itself on the right side because it…

Q: The self-inductance of the circuit in the figure below is 9.20 x 108 H. Find the back emf when the…

A: Given data, theself-inductance is given as L = 9.20 x 10-8 H.The rate of increase in current is .

Q: For the LR circuit shown below, R40 12 & r 5 ms. The switch is closed and 10 ms later the current is…

A:

Q: Write any word problem with the graph below and a 50-mhenry inductor

A: Given,  Inductor = 50 mH We need to :- Write any word problem with given graph and a 50-mhenry…

Q: The voltage across an inductor is proportional to the inductor and the derivative of the current…

A: As we know that,          Voltage across Inductor is given by :…

Q: A solenoid of radius 4.50 cm has 600 turns and a length of 25.0 cm. - (a) Find its inductance. mH…

A: Given the radius  of the solenoid is r=4.50cm=0.045m number of turns N=600 turns  length…

Q: Consider the circuit shown in the figure below. Take = 10.00 V, L = 12 mH, and R = 9 Q. Shown in the…

A:

Q: Find the energy stored in a  7.4-mH  inductor when the current is  3.5 A.  J

A: L=7.4mH=7.4×10-3HI=3.5A

Q: For the circuit shown in the figure below, AV, = 98.0 V, @= 65.0z rad/s, and L = 70.0 mH. Calculate…

A: voltage

Q: Inductive battery chargers, which allow transfer of electrical power without the need for exposed…

A: This question is based on Electromagnetic induction topic. The emf induced in the coils are in…

Q: If a diamagnetic material is introduced into a solenoid that is carrying current I, what happens to…

A: We have to explain what happened to the energy stored here...

Voltage Across Inductor

An actor is a passive electrical component that consists of a coil bent in the form of wire which uses electromagnetism to produce electric current through the coil. When the electric current flows through a conductor that is the coil, a magnetic flux is developed around the conductor. This flow of current through the coil creates a magnetic field based on Fleming's Right-hand thumb rule. If there is any decrease in the current passing through the inductor, then the magnetic field will also decrease and energy is released through the generation of electric current. There is also a secondary voltage inducing in the same coil due to the magnetic flux, since it opposes any changes in the electric current flowing through the circuit. An inductor is also called choke, coil, or solenoid. A choke is designed to block certain frequencies when the DC current passes. A winding coil is coated with insulation to give extra insulation and protect the circuit. They are usually tightly wrapped around a central core which is cylindrical in nature so that the magnetic flux can be induced. The solenoid is a three-dimension coil that is used to exhibit electromagnetism when the magnetic field is developed due to the current flowing through the coil. The sign convention of the inductor is the same as the power dissipating device. When the current flows into the positive side of the voltage across the inductor, the value is positive and the inductor dissipates power whereas when the inductor releases the power back to the circuit, the current has a negative sign convention.