From the following system, obtain the force components for the system X∗ and Y∗ in terms of i and j. It is known that for the system y and x the value of the force components is F = (F76 N i - F500 N j) N . Solve by any analytical method. Check images for the values and image)

From the following system, obtain the force components for the system X∗ and Y∗ in terms of i and j. It is known that for the system y and x the value of the force components is F = (F76 N i - F500 N j) N . Solve by any analytical method. Check images for the values and image)

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter1: Heat, Temperature, And Pressure

Section: Chapter Questions

Problem 17RQ: Convert 22C to Fahrenheit.

See similar textbooks

Similar questions

A left hand threaded 14 mm diameter A36 steel bolt is stuck in a metal block. Assume the bolt head is flush with the block surface at A. In order to remove the bolt the 50 Nm torque is applied to the bolt head as shown. The block applies a resisting torque "t" to the stuck threads which is assumed to be uniformly distributed along the 50 mm buried depth. G = 75 GPa a) Explain the difference between right and left hand threaded bolts Determine: b) The magnitude of the uniform resisting torque "t" (including proper units) c) The internal torque as a function of x measured from B (a FBD is required) d) The maximum shear stress in the bolt Ans: 92.8 MPa e) The angle of twist of bolt head A with respect to end B Ans: 0.0044 rad f) The largest torque that can be applied to the bolt head before it twists off (Tyield = 150 MPa) %3D
240cos10=236.35 N M, =? 240 N A 15° 15° 65° 240sin 10=41.68 N 350 mm M=236.35(0.35) +41.68(0.03)=83.97 N - m 65° (clockwise direction) 30 mm
Wind flows over a flat plate of length L = 25 mm and width W = 8 mm. The plate is maintained at a constant temperature of 32 °C on both sides using an electric heater generating heat at a rate of Q = 0.5 W which is dissipated to air from both sides of the plate. Consider the temperature of the wind/air as 20 °C and assume that the wind speed does not exceed 100 m/s. The properties of air at this temperature are given as; specific heat capacity Cp = 1.005 kJ/kg-K, thermal conductivity k = 0.0253 W/m-K, Density p = 1.19 kg/m³, and kinematic viscosity v = 1.522 x 10 5 m²/s.
D= 1.75 in d= 0.75 in r= .120 in
Please help :( please please M = 1 N = 1
Show the correct FBD please. The answer must be TA=TB=20.4 lb, TC=27.2 lb
topic: torsion in circular shafts The hollow shaft used in the system has the following conditions: Outer diameter (Ø): 150 mm Ø Allowable Shearing Stress: 85 MPa Determine the thickness (mm) of the shaft. Round to the nearest whole number for the thickness and use 2 decimal places for other solved values. Provide a torque diagram, strictly follow instructed sign convention, and start from left to right.
Ex. Find 9 f- 120mm 125mm !30m
3. During tug of war, the bicep muscle generated 4k N force that was perpendicular to the forearm bone. The bicep muscle was attached 4 cm from the elbow joint as shown in figure below. (a) Compute the bending moment at section a-a (b) If a circular solid bone with allowable compressive stress of 130 MPa, what is the minimum permissible radius of the bone?
Da =5 cm D;=3 cm 1 mm mm T=220°C
A cross-section of a beam is shown in Figure Q2. If the shear force in this section is V = 180 KN, determine the value and the location of the maximum shear stress in the section. In Figure Q2, a = 52 mm and the origin of the coordinate system is at centroid of the cross section. A 0 4a Figure Q2 3a
Draw the FBD Use 3 decimal places