From the figure shown, determine the following:a. The plastic moment of the whole beam.b. The order of collapse for each plastic hinges.Design the lightest W shape for each span of the beam. Using A992 Gr. 50 steel.c.250 AN450 KN150 kN60 KNim2.5m3.5 m3m5 m6.5 m

The given structure is a continuous beam with hinged supports. It is asked to find the plastic…

From the figure shown, determine the following: a. The plastic moment of the whole beam. b. The order of collapse for each plastic hinges. c. Design the lightest W shape for each span of the beam. Using A992 Gr. 50 steel. 250 KN 450 kN 150 EN 60 kNm 2.5m 3.5m 3 m 65m

From the figure shown, determine the following: a. The plastic moment of the whole beam. b. The order of collapse for each plastic hinges. c. Design the lightest W shape for each span of the beam. Using A992 Gr. 50 steel. 250 KN 450 kN 150 EN 60 kNm 2.5m 3.5m 3 m 65m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 7.5 ft A P B D F H C E G I P P 6 panels @ 6 ft = 36 ft- K L P

Q: A beam is loaded and supported as shown, where w1 600 Ib/n, w2 388 ft, a-3.7 ft, b 4.6 th, und e-…

A: F1 is the value of triangular load in region x = (0 to a) So, F1 = area of triangular loading

Q: Question 5 of 20 A structural member is fabricated with the cross section show below and is…

Q: 1 m column pinned at the top and MPa. Use NSCP 2015

Q: 30° 30 m PROBLEM 5 TABLE OF ANSWERS: MEMBER NUMBER AF 1 EF 2 DE 3 CD 4 BC 5 AB 6 AD 7 CF 8 BE 9 B…

Q: Answer the following questions with reference to the figure below.

A: Take moment about C :∑ MC=0R26-6002-6004-3002+2002=0R2=633.33kN∑ Fy=0 R1+R2-600-600-200=0…

Q: 1m 4m 20KN 30KN 450 2m B

Q: From the given figure below, determine the minimum height of the beam if the flexural stress is not…

Q: For the beam with the cross-section shown and loads as follows: w-2 kN/m, M-4 kN-mand PkN, P-5.XY…

Q: The cantilevered W530 x 150 beam shown is subjected to a 8.5-kN force F applied by means of a welded…

A: F=8.5kN To find equivalent couple force system at point O

Q: The collapse load for the beam as shown in figure is to G. 3. A. Mp 3. - L/2 L2 He L2

Q: An I-section shown in Fig. is simply supported over a span of 12 m. If the maximum permissible…

Q: From the Given Truss Shown: P= 66 KN M-443 KN Calculate the Force Carried by member FH. If the…

Q: For the truss loaded as shown determine the forces in members FH, GH, and GI in kilonewtons. Use the…

A: Consider the figure,

Q: For the fig. shown, compute the force on each member Of the truss. Indicate whether the member is in…

Q: HW03-02 Note that all internal angles on the truss are 60 degrees. Analyze by Method of Joints. Also…

Q: The beam is loaded as shown. which of the following nearly gives the flexural stress du to tension…

A: Find the reactions :RA=RB=12×4+2×12×12×42=48kNMax moment will be at the midspan…

Q: A W610 x 82 beam of A 36 steel has end reaction of 309 kN and is supported on a plate with a length…

A: Answer We know that End reaction due to web crippling is given by…

Q: A pipe column is braced to prevent bending and buckling. It is subjected to a compressive load of…

Q: 180 mm mm 200 mm A B- 3.2 m 1.5 m 30 mm 30 mm

A: The given data is: Allowable Tensile stress = 4 MPa Allowable Compressive stress = 5 MPa Length of…

Q: properties. f’c= 30 MPa, fc=13.5 MPa, fy=400 MPa, fs=200MPa. e) The moment capacity of the beam…

A: Find lg y1 = 150mmy2 = 350mmA1 =300×200 =60,000 mm2A2 = 600×100 = 60,000 mm2 y= A1y1+A2y2A1+A2y =…

Q: F 2.4 m + 2W 4.8 m 2P. 3.6m 2wn 3P |³P. 3.6 m W24 x 84

Q: : The T- beams sections shown in the figures below. f'c-28 Mpa, fy=420 Mpa. Calculate the design…

Q: Consider the Fink truss shown in (Egure 1). Suppose that F₁-600 lb and F-900 lb. Figure 1 of 1 300…

Q: Find: Calculate the following: Figure a. The gross moment of inertia, Ig b. The location of the…

A: Moment of Inertia:The moment of inertia is defined as the amount indicated by the object opposing…

Q: 5. A frame structure is shown below. The links connected below is a bar with a 30mm by 60mm in…

A: the short of diagram is tanθ=BCABtanθ=68θ=36.869cos θ=x8x=6.4m

Q: predict the maximum stress and deflection in the simply-supported aluminum beam shown below, with h…

A: Given, h = 1 in, b = 10 in, L = 4 ft = 48 in P = 5 psi. Moment of inertia (I)I = bd312I = 10×1312I…

Q: A simply supported beam having a simple span o 8 m must support a uniformly distributed service load…

A: Span (L)= 8 mDead load = 10 KN/m

Q: Given: The T- beam cross section in Figure 3. Find: Calculate the following: a. The gross moment of…

A: Moment of Inertia: The moment of inertia is defined as the amount indicated by the object opposing…

Q: 12.8 The load on the bearing of a cast-iron bracket is 5 kN. The form of the section AB is given.…

Q: What will be the safe weight per linear meter length of the beams if the displacement at E is…

Q: 1. Determine the maximum shear W = 12 KN/m 4m 2m and moment of the beam loaded RI R2 shown.

A: Note: Hi! Thank you for the question As per the honour code, We’ll answer the first question since…

Q: From the figure shown, determine the following: a. The plastic moment of the whole beam. The order…

A: Solution: Find the actual plastic moment: The mechanism for span AB: The maximum moment will occur…

Q: The cantilever beam shown below has the cross-section on the right portion. If the allowable…

Q: Which of the following members shown in the figure is a 2-force member? a. AD b. CB c. AB d. EF

A: Explanation : For a given framed structure, the members DC and EF have no loadings or reaction…

Q: 1500 lb 4500 b A 2.5 m. E NA- ID 1- 96 in. 8 ia

Q: 13 lb, y = 7.94 ft, and the stress in the member is 12.47 ksi . Round off the final answer to two…

Q: Question 27 1 points Save Ans A built up l-section is formed from plates welded together as shown in…

Q: For the given reinforced T-section shown in Figure 2 with fc’= 30 MPa, fy = 400 MPa, calculate the…

A: According to the specifications, first we will calculate the compression and tension type of force.…

Q: Based on the bridge truss show below determine the force acting at members DF, GI, and LM using…

Q: A beam shown below has a T-shaped cross section. Determine the location of maximum compressive…

A: Answer We know from bending equation that F = M*yI F = Bending stress(Tension or compression) M =…

Q: magnitude P as shown. Determine the largest allowable value of P if the working stresses in bending…

A: Cat iron inverted T-section 2 concentrated loads P acting at 1 m and 4 distance from support A…

Concept explainers

Members with compression and bending

Compression members are structural elements that carry compressive axial force. They are the vertical members of a building that support beams and their design, which is governed by buckling and strength. Columns are known as struct or compression members, which are subjected to compressive forces. These members provide stiffness to the building and avoid any imperfection regarding the transfer of axial load. For instance, webs in a truss, braces in a framed structure, tiers, and so on.

Question

From the figure shown, determine the following:
a. The plastic moment of the whole beam.
b. The order of collapse for each plastic hinges.
Design the lightest W shape for each span of the beam. Using A992 Gr. 50 steel.
c.
250 AN
450 KN
150 kN
60 KNim
2.5m
3.5 m
3m
5 m
6.5 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

How to solve this question step by step
Using the Method of Sections, determine the forces in the members listed in the table below for the truss loaded
Determine the design moment capacity of the beam with given properties below. bf = 650mm bw = 350mm tf = 120mm d = 370mm d' = 100mm fc' = 34.5 MPa fy = 400 MPa As = 8 - 28mm bars USE NSCP 2015, Mu = kN-m
A T section of a beam is fabricated from 2 - 12 mm x 150 mm steelplates and joined by welding as shown in Figure ST - 904. It carries a live loadof 6.5 kN/m extending half of its span. Neglect the weight 1. Compute the maximum compressive stress. ( bending stress incompression )2. Compute the maximum tensile stress. ( bending stress intension )3. Compute the maximum shear stress. 4. Compute the shear stress between the junction of web and flange. 5. Compute the maximum deflection. EI is constant.
An 8 m long steel is simply supported at the left end and 2 m from the right end. It carries a total uniform load of 45 kN/m all throughout its length. STEEL DECIGON CIVIL ENGINEERING Beam properties: A= 11,500 mm² bf = 250 mm tw- 10 mm d === 350 mm If=: 16 mm 1x = 266 x 106 mm c) To strengthen the beam, 2- 200 mm x 10 mm cover plates, one at the top of the flange and the other at the bottom of the flange were added. What is the resulting maximum bending stress?
Q2) The members of the truss structure shown below is plain concrete. The compressive strength of the concrete is 25 MPa. Compute the maximum load P that can be carried by the structure. (Cross section of each member of the truss is 200 x 200 mm and don't use material factors and do not consider slenderness) Comment on your results briefly. P A& 2m SC 2 m 1380 2m D
Solve carefully
AURS RA= RC = L1 RF = Consider the following values in the given beam above: L1 = 6 m L2= 2 m L3 = 4 m L4 = 2 m L5 = 2 m L6 = 1 m W1 = 90 kN/m W2 = 20 kN/m P = 40 KN M = 50 kN-m External support reactions: B KN W1 KN kN L2 H- The maximum shear along the entire span of the beam is The maximum positive moment along the entire span of the beam is The maximum positive moment along the entire span of the beam is D L3 P 2 m kN. E W2 kN-m. kN-m. L4 F L5 M G L6 Express all your answers in three decimal places. For the reactions, there is NO NEED to put the sign. For V and M values, ALWAYS include the sign (+ or -) to denote the nature of shear and bending. Not indicating the sign will mark your answer wrong. No considerations. H
A frame structure is shown below. The links connected below is a bar with a 30mm by 60mm in section. Find the Allowable lad P that can be applied so that the stresses will not exceed 100MPa in tension or 80Mpa in compression.
A simply supported pre-tensioned T-beam, as shown in Figure (2) has: f'ci 25MPa; f'-40 MPa; span length is 12m; Total Aps-800mm² for tendons; initially stress in the tendons is 1000 MPa. Consider 20% the total losses of pre stressed force then determine the allowable service live load can be carrying. 150mm 600mm T 500mm T Aps-800 mm² 50mm 150mm Typical Cross section Figure (2)
Mechanics of deformable bodies
For the T profile made of wood in the figure, the normal safety stresses are (ϭsafe) tensile = 50MPa and (ϭsafe) pressure = 70MPa in case of tensile and compression.a) Calculate the section moment of inertia.b) Calculate the largest and smallest normal stresses that will occur in the section.c) Determine whether the applied force can be safely carried.