From the constant head permeability test, the following values are given: Void ratio of specimen Length of soil sample 0.46 450 mm Constant head difference 700 mm Water collected in a period of 180 seconds Cross-sectional area of soil sample 3.54 x 10-4 m³ 2.26 x 10-3 m² a.) Determine the coefficient of permeability in m/hour. b.) Compute the discharge velocity in mm/s. c.) Compute the seepage velocity in mm/s.

From the constant head permeability test, the following values are given: Void ratio of specimen Length of soil sample 0.46 450 mm Constant head difference 700 mm Water collected in a period of 180 seconds Cross-sectional area of soil sample 3.54 x 10-4 m³ 2.26 x 10-3 m² a.) Determine the coefficient of permeability in m/hour. b.) Compute the discharge velocity in mm/s. c.) Compute the seepage velocity in mm/s.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Consider that a 58.7 gram sample of dry soil is used in making a mechanical analysis by using the hydrometer method. The laboratory was held at a constant temperature of 20 C (68 F). The 40 s hydrometer reading was found to be 32.5 and the 8 hr hydrometer reading was 15.5. The percentage of sand in this soil sample is (note, a 58.7 gram sample is used here): Your Answer: Answer units
A constant-head test was conducted on a sample of soil 15cm long and 60 cm^2 in cross-sectional area. The quantiities of water collected was 50 cm^3 in 20 seconds undera a head difference of 24 cm. Calculate the hydraulic conductivity. If the porosity of sand is 55%, calculate the average velocity and the seepage velocity. Estimate the hydraulic conductivity of a similar soil with a porosity of 35% from the results test. Please show all work!!
The data from a falling-head test on a silty clay are: Cross sectional area of soil = 1000 mm^2 Length of soil sample = 200 mm Area of stand pipe = 40 mm^2 Head difference at time t = 0 is 500 mm Head difference at time t = 3 min is 300 mm a) Determine the hydraulic conductivity of the soil in cm/sec. b) What is the head difference at time t = 100 sec in mm
PROBLEM C For a falling head laboratory test, the following are the given values: • Length of soil specimen 210.00 mm Initial head 523.00 mm Final head 297.00 mm = Duration of test 3.50 mins 42.0 sq.mm 1050.00 sq.mm Area of standpipe Area of specimen A. Compute for the hydraulic conductivity of the soil in cm/sec. B. Determine the seepage velocity if n=0.35 C. Determine the head difference at t = 120 sec
For a falling head permeability test, the following are given: length of specimen is 360 mm, area of specimen is 70 cm2 , and hydraulic conductivity of soil specimen is 0.165 cm/min. what should be the area of the stand pipe for the head to drop from 700cm to 360cm in 7 mins? compute the seepage velocity under the test condition if the soil specimen has a void ratio of 0.55 in cm/sec compute the head difference at time equal to 5 minutes?
The attached figure shows the soil sample prepared and setup for constant head permeability test. If the permeability of the soil is 4.5 x 10-3 cm/sec, what is the required time to collect 100 ml of outflow water under the steady state condition? 40 cm Soil in the pipe with internal diameter 20 cm Outflow collection 50 cm 40⁰ 90 cm -Datum- 10 cm
In a constant head permeability test in the laboratory as shown in Figure Q2(e), the data is recorded in Table Q2(b). The void ratio of the soil specimen is 0.46. Determine; (i) Hydraulic conductivity, k, of the soil in cm/sec. (ii) Discharge velocity in cm/sec.
In a falling head permeameter, the sample used is 25 cm long having a cross-sectional area of 24 cm2. The cross-sectional area of the standpipe is 2 cm2. The sample of soil is made of three layers perpendicular to the direction of the flow. The thickness of the top layer is 8 cm and has a value of k1 = 4 x 10-4 cm/sec, the second layer of thickness 10 cm has k2 = 6 x 10-4 cm/sec, and the bottom layer of thickness 7 cm has k3 = 8 x 10-4 cm/sec. Calculate the time required for a drop of head from 25 to 12 cm. ( in minutes).
A sample of sand is subjected to a constant head permeability test. The sample diameter is 60 mm and its length is 130 mm. Under an applied head of 60 cm, 119 cm³ of water flows through the sample in 5 minutes. Determine (a) the coefficient of permeability, and (b) the discharge velocity.
For each of the three cases shown in Figure 3 determine: a). the pressure head, elevation head, total head, and cumulative head loss at the entrance, exit and point A of the soil sample. For each case, set the datum at the tail water elevation. b). the discharge velocity and the seepage velocity if the soil's permeability coefficient is 0.10 cm/s and the porosity is 40%. POTTAWA c). the discharge velocity and the seepage velocity if the soil's permeability coefficient is 0.001 cm/s and the void ratio is 0.600. BAINA LE DROIT 3 m 4m + 2m A. Case I ez ilise ROTÉGÉ PAR 3 m 1m 4m est cadre A. Case II sirez 1 m e mate ificati Figure 2 dood 3 m 5 m TED MATERIA Case III urse are rected by cop not harmission to up nox clarification, ple 1 m
For a falling-head permeability test, the following values are given:• Length of specimen 8 in.• Area of soil specimen 1.6 in.2• Area of standpipe 0.06 in.2• Head difference at time t 0 20 in.• Head difference at time t 180 sec 12 in.Determine the hydraulic conductivity of the soil in in./sec
For a constant laboratory permeability test on a fine sand, the following data are given: Length of specimen: 18 cm. Diameter of specimen: 95 mm. Constant head difference: 54 cm. Volume of water collected in 4.10 min.: 423 cc Void ratio of the soil specimen: 0.54 Determine the seepage velocity in m/min.