Friction angle of dry sand is 330. In a direct shear test on this sand, a normal stress of 100kPa was applied. What shear stress will cause the failure? (a) 154kPa (b) 100kPa (c) 78kPa CD GELD

Q: 3. A car has an initial speed of 25 m/s and a constant deceleration of 3 m/s^2. Determine the…

A: Using equations:v-u=atv2-u2=2ass=ut+12at2

Q: 2. The rigid bar BC weighs 50 lb/ft, is supported by the steel rod AC of cross-sectional area of…

A:

Q: Solve the boundary value problem of y" +25y = 0 where boundary conditions y' (0) = 6, y' (π) = -9

A:

Q: Solve for the Shear and Bending moment equations. Show their diagrams. 12 kN/m 6m 18 kN/m 80 kN/m 6…

A:

Q: Question 5 of 20 A structural member is fabricated with the cross section show below and is…

A:

Q: To the calculated area of cover plates of a build up beam, an allowance for rivet holes to be added…

A:

Q: A continuous beam is carrying a triangular load as shown. An internal hinge at B allows the system…

A:

Q: If versine of 0 = 0.48, find the value of 0 in degrees. Select one: O a. 58.67° O b. 47.84° O c.…

A:

Q: Problem 1 Resolve the 900-N force into a component P along with AB and a component Q perpendicular…

A:

Q: Q.2.8 MASS FLOW AT A PIPE JUNCTION Consider the s. tv low in a water pipc joint shown in the…

A:

Q: In a laboratory, researchers conducted an experiment on soil with 13.25% water content, compacting…

A: Note: As per Bartleby Guidelines, only first three subparts will be discussed in the solution. But…

Q: Fill out the blanks in following statement. The removal of substances from water is accomplished by…

A:

Q: Part A Determine the depth y that will produce maximum velocity for the flow. Express your answer in…

A: Hydraulic Characteristic of circular sewer:  As in the figure the sewer shown in figure, is circular…

Q: If the center of gravity of a ship in the upright position is 10 m above the center of gravity of…

A:

Q: The uniform beam has a mass of 48 kg per meter of length. Determine the reactions at the supports. A…

A: Given Data  Uniform beam has a mass of 48 kg/m  Find the support reaction in terms of Netwon(N).

Q: If A is 8% taller than B, while B is 9% taller than C, by how much in percent is A taller than C?…

A: given  A is 8% taller than B B  is 9% taller than C  It means A=1.08 B               B = 1.09 C

Q: What type of concrete additives (two additives each) would you suggest for casting (a) the same…

A: a) To accelerate the rate of strength of concrete production or to decrease concrete curing…

Q: A bored pile of 0.8 m in diameter is constructed in sand. Soil conditions and relevant soil…

A:

Q: Homework: (Column Strength Interaction Diagram ) Assume equal rebar at four sides Check if a column…

A:

Q: Determine the force (magnitude and type, tension or compression) in all members of the roof truss…

A: Consider the figure, Here, T is the tension and C is the compression.

Q: The hydraulic conductivity, k of a soil is 7.15 x10-°cm/s at a temperature of 20° C. Determine its…

A:

Q: Q8 Which of the following requires an LRFD strength reduction factor of 0.9 for overall member…

A:

Q: Review Water flows at 25 ft³/s in the channel, which is originally 6 ft wide and then gradually…

A:

Q: 4. Determine the distance 'a' as a fraction of the beam's length 'L' for locating the roller support…

A: Given moment at B should be zero. I have considered the moment at B from right end side .

Q: A steel [E = 200 GPa ] rod with a circular cross section is 20 m long. Determine the minimum…

A:

Q: A Site requires 250,000 m3 of soil having a void ratio of 0.45, determine the required volume of…

A: Please refer the attached image for complete solution. THANK YOU.

Q: Two columns are 4,506 mm away from each other measured center to center. The loads supported by the…

A: Structures are by and large intended to have solid section frail shaft frameworks, where such…

Q: Determine the moment of inertia with respect to the horizontal centroid of the figure. 250 38 300 25…

A: A section have been given and it has been asked to determine moment of inertia about horizontal…

Q: For each structure shown, compute the reactions and draw shear and bending moment diagrams. Indicate…

A: Given:Required :Support reactions,  shear force diagram and bending moment diagram

Q: If each pulley has a mass of 5 kg, what is the mass "M" that will hold the system in equilibrium?…

A: solution  we can solve by drawing free body diagrams of each pulley  Note : The tension along on…

Q: Complete solutions. Show free body diagrams. A long zipline carries two cable cars with a combined…

A: find the i.Mass of cable car X (kg) ii.Mass of cable car Y (kg) iii.Tension in cable AB (KN) iv.…

Q: member. (a) Dctermine the coordinates yR and Za of the point where the tensile load P must act in…

A: Please find the answer in the below attachments

Q: The force F has a magnitude of 710 N. Express F as a vector in terms of the unit vectors i and j.…

A:

Q: A five-course traverse was measured in the field as shown in the figure. 1. Compute the balanced…

A: We are given that Backbearing of line = forbearing of line + 180o                ( when azimuth of…

Q: The hydraulic conductivity, k of a soil is 8.26 x10-°cm/s at a temperature of 20° C. Determine its…

A:

Q: 1.5P KN P kN- A a. -21.3 kN b. -21.9 kN c. -20.6 kN d. 17.5 kN 1.5 m GH 3 m Force at member GH -3 m…

A:

Q: 0.656 ft * = 30° Y = 121 Iby Fig 2. ig 1. 15 ft 20 ft |H = 23.41 fA 8,= 117 #F 9 =34°1 1.25 0.8 1.5…

A:

Q: For each structure shown, compute the reactions and draw shear and bending moment diagrams. Indicate…

A:

Q: 4. A mass m is on a frictionless incline that makes an angle 0 with the horizontal. Let m = 25.0 kg…

A: solution: m=25kg  theta = 300

Q: Please help. Thank you!

A:

Q: Use the virtual work method to determine the slope and deflection at point D of the beam shown. -15…

A:

Planar Stresses