اكتب هنا FREE-BODY DIAGRAM EXERCISES 3/A In each of the five following examples, the body to be isolated is shown in the left-hand diagram, and an in- complete free-body diagram (FBD) of the isolated body is shown on the right. Add whatever forces are nec- essary in each case to form a complete free-body dia- gram. The weights of the bodies are negligible unless otherwise indicated. Dimensions and numerical values are omitted for simplicity. Body Incomplete FBD 1. Bell crank supporting mass m with pin support at A. mg T m Flexible cable A Pull P 2. Control lever applying torque to shaft at 0. Fo 3. Boom OA, of negligible mass compared with mass m. Boom hinged at O and supported by hoisting cable at B. B m mg

Q: I can't find C or D

A: Draw the free-body diagram.

Q: A block-and-tackle pulley hoist is suspended in a warehouse by ropes of lengths 2 m and 3 m. The…

A:

Q: The tension is 850 lb in cable AB and 950 lb in cable AC. y B 45 in. Wood Floor 40 in. C 60 in. 65…

A:

Q: The resultant couple moment acting on the triangular block is to be zero. (Figure 1) Take F₁ = 15…

A:

Q: 1- Determine the resultant of the forces which shown in figure pila a F= 300 lb F-150 lb 37 55 13 Fy…

A:

Q: 1. The hanging box is being pulled by two ropes T1 and T2 as shown below. T1 = 565 Newtons and T2 =…

A:

Q: F = 100 lb F = 18 kips %3D 65 30° 750 70°

A: For solution refer below images.

Q: 3) if the applied forces F= 78O lb, F2= 440 lb, and F3= 960 lb, what is the force in member BC?…

A:

Q: Need help with all four questions please. Include units all steps. Thanks.

A:

Q: A=25 504 (2-49. The 25-1b force R'in Fig. P2-49 is tiro resuzitant of four forces, three of which…

A:

Q: Statics of Rigid Bodies *Replace the force system with a single replacement. *What is Vertical…

A: Given data: F1=9.33538 kNF2=6.77171 kNM=25.68668 kN·m Need to determine the vertical component of…

Q: Q.1) Draw a Free Body Diagram for each object indicated below. Include values for known forces and…

A: (a) Draw the given diagram.

Q: Three forces are acting on the problem. List all of the simplifications that can be used in the…

A:

Q: In the figure below, the masses of each object are: m₁ = 2.00 kg, m₂ = 2.00 kg, m3 = 3.00 kg. The…

A: The masses are the dimesnion are .

Q: F2-13. Determine its coordinate direction angles of the force. F=75 lb

A: We can answer the first question since the exact one is not specified. Please resubmit the question…

Q: If a 200 N force F1 is applied to the piston with the 4 cm diameter, what is the magnitude of the…

A: The step by step solution is provided below.

Q: What would be the resultant force F of the triangular distributed load and its location d measured…

A:

Q: 2. The crate weighs 450 kg and is supported by three cables as shown in the figure 2m below. 1m a.…

A:

Q: mathal 220 N/m 890 N/m 6 m Figure P-238

A:

Q: 1.)Given and requirement(s) 2.)Free body diagram 3.) Formulas and its proper symbols 4.)…

A:

Q: Horizontal Component of the force at B: Vertical Component of the force at B: Horizontal Component…

A:

Q: The horizontal and vertical components of several forces are: (a) Ph = -200 lb and F=-200 lb; (c)…

A:

Q: The figure below shows a steel structure made up of two pre-assembled segments that are hoisted by a…

A:

Q: If the crate in the image weighs 38.0 lb, What is the Force in Cable AD (lb)?

A:

Q: 52 Given F₁ 501b g=32.174 ft₂ Required: m=? Equation: F₁ = mg; m² mq; m-k = K g Solution: Answer m =…

A:

Q: 1. Measure di and d2 and record the values. 2. Record the total mass, M2, and include the mass of…

A: Given: The distance are d1=0.1 m and d2=0.1 m. The mass is M2=14 gm. The angle is θ=30°. The…

Q: The following diagram corresponds to questions 1 to 3. A beam rests on two sharp edges as shown on…

A:

Q: Given: T= 300 N,P = 450 N,F = 200 N, A = 45, B= 30°,C 20 Find: magnitude and direction from u axis,…

A:

Q: FIND THE FOLLOWING SHAPE WEIGHT CENTER BY REFERENCES O point.

A: Write the expression of distance c.

Q: A plate of uniform mass is supported in the horizontal position by two hinges and one bar. The…

A: As per guidelines we are supposed to answer only the  first three parts of a question

Q: For multiple choice, choose the best answer. Show all work: indicate your plan and draw FBD's (Free…

A:

Q: Q1: Find the result of the system of converging forces in Figure (1).

A:

Q: 42 in 64 [in]- 50 in D 59 in 63 in +10 in ... 21 in SAR (

A: Given,

Q: Learning Goal: To learn to apply the method of joints to a truss in a systematic way and thereby…

A:

Q: Given the diagram below, determine the following: 3 m 2 m 2m Im im-1.5m. 1.5m 15m 3 kN 3.m 2m 4 kN…

A: Position vector is obtained by subtracting the head co-ordinates of a vector from its tail…

Q: | 45-lb force is required to operate the foot pedal. Determine the force exerted by the bearing 'O'…

A:

Q: Find the each force of FAB, FAC and FAD

A:

Q: For the figure shown if the tension in rope AD is 180 lb find the angle between AD and AB, and then…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.