Four steel bars jointly support a mass of 15 Mg as shown in Fig. P-276. Each bar has a cross-sectional area of 600 mm2. Find the load carried by each bar after a temperature rise of 50°C. Assume a = 11.7 pm/(m-°C) and E = 200 GPa. 60° 15° 15° Figure P-276 15 Mg

Four steel bars jointly support a mass of 15 Mg as shown in Fig. P-276. Each bar has a cross-sectional area of 600 mm2. Find the load carried by each bar after a temperature rise of 50°C. Assume a = 11.7 pm/(m-°C) and E = 200 GPa. 60° 15° 15° Figure P-276 15 Mg

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1 A rigid block AB of weight W hangs on three equally spaced vertical wires, two of steel and one of aluminium as shown in Figure Q1. The wires also support a load P acting at the centre of the block. The diameter of the steel wires is 4 mm and the diameter of the aluminium wire is 6 mm. The allowable stress in the steel wires is 140 Mpa and in the aluminium wire is 80 MPa (Assume W = 400 N, E, 210 Gpa and E, -70 Gpa). (a) Draw the free body diagram for the rigid block. (b) Determine the load P can be supported for the steel. (c) Determine the load P can be supported for the aluminium. TH
The structure below is made from stock (same stock for A-B-C and B-D) that is 5 mm thick (into the page) and b mm wide. The material is steel with: E = 200 GPa Sy 3D 400 MPа b) Describe in words how you would determine the horizontal displacement at B due to the load applied at A. 135 mm Clearly state any assumptions. 240 mm→ D b. 450 mm 510 mm В 120 mm A 4000 N
AB and CD caps of the same material are tightly fitted on both ends of the 24 mm diameter AD steel bar. a) Find the pull force P that will make the total elongation of the system 0.04 mm. b) Calculate the extension amount of BC part by the force P you found. Take the elastic modulus E = 200 GPa. 36mm 24mmr 36mm 48mm D 28mm
A steel bar of 30 mm * 30 mm square cross section is subjected to an axial compressive load of 300KN. If the length of the bar is 3m and E=200GPa find contraction of the bar.
A rigid beam is supported by a pin at A and two metallic wires at B and C. Determine the force P that causes the point C to displace downward by 0.1 mm. Given: E (wire B) = 70 Gpa, E (wire C) = 200 Gpa and both wires have a diameter D = 6 mm. Consider a linear elastic behavior. Select one: P = 597 N P = 537 N P = 430 N P = 573 N P = 287 N
(a.)The figure below shows a steel rod of 25mm² cross-sectional area. It is loaded at four points K, L M, and N. Assume Esteel = 200GPA. Find the total change in length of the rod due to the four loadings. M 100N 250N 200N 50N 500mm 400mm 1700mm Figure Q.la: Steel rod
The rigid beam AD shown carries a load W = 200 kN. It is supported by a hinge at D, a steel rod at A, and a bronze rod at C. The material properties are shown in the table below. Calculate the tensile forces in the steel and bronze rods after the load W is applied into the beam. Neglect the weight of the beam. Material E (GPa) A (mm2) Bronze 83 1290 3 m Steel 200 320 Bronze Steel 1 m 1m A B -1.2 m 2.4 m W = 200 kN
i need the answer quickly
3. The bar shown below is composed of two pieces, AC and CD. The bar is attached to the wall at point A. The length L = 10 in. The cross sectional areas are: AAC = 4 in? and AcD = 2 in?. The Young's Moduli are: EAC =20 Msi and Ecd= 15 Msi Two forces are applied at points B and D: PB = 50 kips and PD = 20 kips. Determine: (a) the reaction force at A (specify –→ or +) and (b) the deflection of point D (specify → or +). (Hint for (b): Think about how many pieces you must subdivide the rod into.) Ans: RA = 30 kips (+), dp = 7.9167×10-3 in (E) A В C D Pp L 2L L
Problem 3: (M4) Your boss at a construction company asked you to verify the thickness of a 3 m long hollow-square steel column (E=200 GPA) that can withstand an axial compressive load of 50 MN, the outer dimension a is 400 mm. The column's cross section is shown in Figure.4. Assume the column is a fixed-free type. b Figure.4: Cross-section of a hollow-square steel column
Please show complete solution and box the final answer
Problem 3: (MМ4) Your boss at a construction company asked you to verify the thickness of a 3 m long hollow-square steel column (E=200 GPA) that can withstand an axial compressive load of 50 MN, the outer dimension a is 400 mm. The column's cross section is shown in Figure.4. Assume the column is a fixed-free type. a b Figure.4: Cross-section of a hollow-square steel column