Four resistors R1=190 ohm, R2=330 ohm, R3=330 ohm and R4=50 ohm are connected to a 36 V battery as shown in the diagram below. R1 a R2 R3 R4 i) What is the effective resistance of the circuit? ii) What is the reading of ammeter? iii) What is the voltage across R1 (between the points a and b)? iv) What+ is the voltage across P2 and P3 (between

Four resistors R1=190 ohm, R2=330 ohm, R3=330 ohm and R4=50 ohm are connected to a 36 V battery as shown in the diagram below. R1 a R2 R3 R4 i) What is the effective resistance of the circuit? ii) What is the reading of ammeter? iii) What is the voltage across R1 (between the points a and b)? iv) What+ is the voltage across P2 and P3 (between

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What is the equivalent resistance value of this circuit?
The three series resistors R1,R2 and R3, what is the value of resistor R1 if voltage V1=25 V and total resistance equal 15 ohm and total voltages equal 50 V. A. 7 ohm B. 6.5 ohm C. 7.5 ohm
Part 1 After using the UT33B multimeter to check the voltage of the batteries and the resistance of, light bulb and resistors, these are the results: - Voltage of the battery is measured to be 1608 mV, The scale used to measure voltage is 2000mV on the UT33B multimeter - Resistance of the bulb is measured to be 0.24 ohm, The scale used to measure resistance is 200 ohm on the UT33B multimeter - Resistance of the resistor1 (R1) is measured to be 15.2 ohm, The scale used to measure resistance is 200 ohm on the UT33B multimeter - Resistance of the resistor2 (R2) is measured to be 27.2 ohm, The scale used to measure resistance is 200 ohm on the UT33B multimeter Part 2 After connecting a circuit to find the resistance of the light bulb and resistors experimentally using a circuit, these are the results: LIGHT BULB - Resistance of the light bulb and resistors could not be measured on the UT33B multimeter, so the voltage and current were measured and the resistance was found using ohms law.…
Find the current in each of the resistors using Kirchhoff’s Laws.
In the circuit in figure, the emf from the battery is equal to 30 V, L= 5H, R1 = 10 ohms and R2 = 20 ohms. Calculate how much time has to pass after closing the switch K for the current in the resistors to be the same. R, D
The circuit shown Figure has a current of 2.5 mA. Find the following quantities: a. The total resistance of the circuit. R 3.3 k E-45 V b. The value of the unknown resistance, R2. c. The voltage drop across each resistor in the circuit. d. The power dissipated by each resistor in the circuit. R2 1- 2.5 mA R3- 5.6 ka
2) What doping of Phosphorus (n-type) do you need to make an 1206 resistor have a resistance of 1200 Ohms? The dimensions of an 1206 resistor are L = 3.20mm, W = 1.60mm, H= 0.95mm
What is the total resistance and current in the circuit? 552 www wwwwwwww 352 2222 4V THE
Select the three True statements about voltage and resistors in series below
Consider the circuit shown below. Determine the maximum power that can be transferred to the external load at the terminals a-b. Use the following values: R1=R2=R3=R4 = 10 ohm, V=55 V. Report the value with one significant digit after the decimal point. Please answer in typing format please
Determine the resistances below based upon the figure below. The symbol below R3 means ground (voltage is zero between R3 and R4). Note the current and resistance units. The 100 V refers to the voltage added by the battery, not necessarily the voltage at the battery. 0+48 V R1 R o+12 V 16 mA 100 V R4 0-20 V R1= kQ R2= kQ R3= kQ R4= kQ
Given two batteries: one with voltage V and internal resistance r1; another with also voltage V and internal resistance r2. Which of the following is true if we connect them in series facing the opposite direction? No voltage will remain, while the total internal resistance will be r1 + r2. The total voltage will be -V, while the total internal resistance will be r1 + r2. The total voltage will be -2V, while the total internal resistance will be r1 + r2. The answer can be found on the other choices.