Four channels, two with a bit rate of 200 kbps and two with a bit rate of 150 kbps, are to be multiplexed using multiple slot TDM with no synchronization bits. Answer the following questions: a. What is the size of a frame in bits? b. What is the frame rate? c. What is the duration of a frame?

Four channels, two with a bit rate of 200 kbps and two with a bit rate of 150 kbps, are to be multiplexed using multiple slot TDM with no synchronization bits. Answer the following questions: a. What is the size of a frame in bits? b. What is the frame rate? c. What is the duration of a frame?

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

We need to use Synchronous Time Division Multiplexing to combine 17 different channels, where 10 channels are each of 300 Kbps and 7 channels are each of 600 Kbps. A unit is 1 bit. Now, answer the following questions using multilevel TDM with no synchronization bit. Your answers must have units. i) What is the output bit duration? ii) What is the size of an output frame in bits? iii) What is the input bit duration?
III. The figure below shows synchronous TDM, the data rate for each input connection is 1 Mbps. If 1 bit at a time is multiplexed, Find (a) the input bit duration, (b) the output bit duration, (c) the output bit rate, and (d) the 1 1 Mbps ... output frame rate. Frames 1 Mbps ... MUX ... I Mbps .... 1 I Mbps
I need the answer quickly
Question 04. We need to use synchronous TDM and combine 20 digital sources, each of 100 Kbps. Each output slot carries 1 bit from each digital source, but one extra bit is added to each frame for synchronization. Answer the following questions: a. What is the size of an output frame in bits? b. What is the output frame rate?c. What is the duration of an output frame? d. What is the output data rate? e. What is the efficiency of the system (ratio of useful bits to the total bits).
Suppose that the spectrum of a channel is 2 MHz, and an intended capacity is of 8 Mbps, then the SNR is .............. in order to obtain this capacity 8 04 O 15 O 17 O 16
We have 14 sources, each creating 500 8-bit characters per second. Since only some of these sources are active at any moment, we use statistical TDM to combine these sources using character interleaving. Each frame carries 6 slots at a time, but we need to add four-bit addresses to each slot. Answer the following questions: a. What is the size of an output frame in bits? The output b. What is frame rate? c. What is the duration of an output frame?
How many bytes of data can be transferred in 10 seconds via a serial link in asynchronous mode with a baud rate of 2800 and three parity bits and two stop bits in the frame?
We need to use synchronous TDM and combine 20 digital sources, each of 100 Kbps. Each butput slot carries 1 bit from each digital sources, but one extra bit is added to each frame for synchronization. Answer the following questions: a. What is the size of an output frame in bits? b. What is the output frame rate? c. What is the duration of an output frame? d. What is the output data rate? e. What is the efficiency of the system (ratio of useful bits to the total bits).
Question 3d Recall that the maximum input voltage for a 12-bit ADC on the TM4C is 3.3 V. If the input voltage on analog input channel 2 (AIN2) is 0.75 V, what is the value of the digital result after conversion? Possible answers are given in decimal. 930 930.9 232 931 3072
2. (a) In FDM, time synchronization is not necessary. Yes or No? Give proper reasons behind your answer. Write one example of TDM where extra information load (overhead) could be 300%.. (b) We need to use Time Division Multiplexing and combine 9 digital sources, each of 900 Kbps. Each output slot carries 9 bit from each digital source, but no extra bit is added to each frame for synchronization. Now, answer the following questions: i) What is the output frame duration? ii) What is the output frame rate? iii) What is the output bit rate? iv) What is the output bit duration? v) What is the size of an output frame in bits? vi) What is the input bit duration?
What is the channel capacity for a signal power of 100 W, noise power of 20 W and a bandwidth of 4 kHz of a digital system?
(a) Compare the terms Throughput and Goodput. (b) Describe the principle of Manchester Signaling encoding scheme. (c) Decode the following digital signal using NRZ.