Forces of 5 Nare applied to the handles of the pa-Determine the force exertedper punch shown in Fig.on the paper at D and the force exerted on the pin at B byhandle ABC.5NE-70 mm40 mm5N

Consider the free body diagram of the single lever as shown below. Here,

Answered: Forces of 5 Nare applied to the handles…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A rectangular plate is supported by three cables as shown. 480 250 360 130 320 360 X 450 Dimensions in mm a. What is the angle formed by AB and AC? b. If the tension on wire DA is 150OON, determine the components Fx, Fy, Fz of the force acting on the rectangular plate through wire DA. Express your answer in unit-vector form. c. Compute for the direction of the force F based on the +y axis, 0 _ .
A cable is connected to an L shaped arm OAB as shown. The magnitude off the tensile force on the cable is given as T = 2500 and angle between the segment AB of the L- shaped arm and cable = 91.229 degrees. ( use the vector approach ) A) determine the components of the tensile force on the cable which are parallel and perpendicular to segment AB of the L-shaped arm
Each truss member acts as a two-force member. When a force is developed in a member, the force is either compressive or tensile. Complete the free-body diagram of the two truss members by adding the forces that act on them. The upper left member is in compression and the lower right member is in tension. Compressive forces should terminate at the joint. Tensile forces should originate at the joint. Draw the vectors starting or ending at the appropriate black dots. The location and orientation of the vectors will be graded. The length of the vectors will not be graded. Ⓒ No elements selected Select the elements from the list and add them to the canvas setting the appropriate attributes.
Kindly write the full solution on a piece of paper rounded off to 4 decimal places, much appreciated
Don't copy any other source
Three forces are applied to the frontof the car in the figure. Determine themagnitude of the force F3 and the resultant force if the direction of the resultant is on the x-axis.Solve the problem using decompositionof forces in rectangular components.
1-2 A joint which connects two members of the truss is carrying loads as shown. a) With a simple diagram, explain how a given force can be resolved into its rectangular components and can be represented in a vector form accordingly. *. b) (i) Express FAB in its rectangular components using the Cartesian coordinates given that the magnitude of EAB is 13 N. (ii) Find the resultant of the 12-N and 15-N loads. (iii) Determine the magnitude of FAC and the angle e required for static equilibrium. c) Assess the condition of equilibrium if EAC is directed vertically i.e. 0 = 0°. [b) (i) FAB=-12 i +5j N; (ii) R=-2.1 i-20.2 i N or R = 20.31 N and 84.1°; (iii) FAC = 20.7 N and = 42.8%] B 0.5 m Figure 1.2 m P1-2 EAB 12 N 0 FAC 60⁰ x 15 N
pls help me :( im not too good at this
Compute the force in each cord. B. 105 90 30 30 75 300 lb D. 400 lb
2-13 The force acting on the gear tooth is F 20 tb. Resolve this force into two components acting along the lines aa and bb.
Beplace the force 0homin.fig by Couple and. force acted at.poiat B. 6 cm
solve all parts

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Forces of 5 Nare applied to the handles of the pa- Determine the force exerted per punch shown in Fig. on the paper at D and the force exerted on the pin at B by handle ABC. 5N E -70 mm 40 mm 5N