For three hinge arch shown in Figure 4. Which is subjected to U.D.L. determine the tensile force for different value at location x = 15 ft. & 60 ft for different height of h=12, 24, 36, 48, 60 ft. L 60' w = 6 kips/ft B hinge + Figure 4. 60'-

Q: Explain and differentiate between static and kinematic indeterminac

A: In statics, a construction is statically uncertain (or hyperstatic) when the static harmony…

Q: Please explain how you got the location of the resultant, how did you take the moment of each area,…

A:

Q: What is kinematics? What is meant by pitch, yaw and roll?

A:

Q: 40N 30 DEG 30N A 15N ANGLE THETA F

A:

Q: 3. Calculate the moment of inertia of the shaded area about the x and y axes. 100 + 100 50 50 -75 75…

A: Concept Here we will use parallel axis theorem to calculate the moment of inertia.

Q: 3. Calculate the moment of inertia of the shaded area about the x and y axes. 100 + 100 50 50 -75 75…

A:

Q: rizontal reinforcing bar yers. Use the length of

A: SOLUTION  no. of horizontal bars =206=326 in one layer N04 = 4 bars in one layer   in three 3 layers…

Q: Write the formula for the effective length factor?

A: The effective length factors of columns  plays major role in the design of compression members.…

Q: Problem: Replace the force system acting on the post by a resultant force, and specify where its…

A:

Q: Explain Improving Stability of Slopes.

A: Stability of slope is an important topic of study in geo-technical engineering and is defined as the…

Q: What is pitot tube? Briefly describe and support your explanation with appropriate equation and…

A: A Pitot tube is a pressure measurement instrument used t measure fluid flow velocity. The pitot tube…

Q: 4. Find the centroid of the figure shown. y 30⁰ 30⁰ X

A:

Q: Determine the coordinates of the centroid of the shaded area. y | 25 E 50 60 25 60 70 50. --x 170…

A:

Q: is required to find soil pressure at a depth of 10 ft beneath the interior corner A and exterior…

A:

Q: Explain Dilatometer Method.

A: Dilatometry is a method by which a material's dimensional changes are characterized as a function of…

Q: Add 1 cm and 1 m A. 50 cm B. 101 cm C. 250 m D. 150 m

A: Given data : 1 cm , 1m Since , we know that : 1m = 100cm

Q: Which of the following most nearly gives the total degree of indeterminacy? 105 130 36 O O 55

A:

Q: Determine the coordinates of the centroid of the shaded area. y 15 30 - 40 15 35 40 25 105…

A:

Q: Determine the cross sectional area of the given cross section notes: LEFTMOST LEFT CENTER RIGHT…

A:

Q: Determine the coordinates of the centroid of the shaded area. y 30 E 55 -70 30 60 60 I 50 -x 195…

A:

Q: What are the possible applications of hyperbolic geometry applied in the real world'

A: Brief concept introduction- Hyperbolic geometry- Hyperbolic geometry, is a non-Euclidean geometry…

Q: Locate the x position of the centroid for the parabolic area. Type your answer including units…

A:

Q: Do you know what is Parallax and Distance Measurement?

A:

Q: Briefly explain the drawback of plate earthling in system earthing.

A: Electrical earthing is the practise of transmitting the quick discharge of electrical energy with…

Q: What do you mean by Eddy in the atmosphere?

A: Answer:- Eddy: Small eddies takes place in day time in earths atmosphere, when surface air is heat…

Q: How do I find the horizontal analysis

A: Horizontal Analysis of financial statements is an analysis method that represents the changes that…

Q: Given the same questions. What if the a is AB, S 29° 42’ E      and b is AC, N 57° 18’ E

A:

Q: Pitched roof Cavity wall Brick wall Floor Dead Load (kN/m2) 2.1 3.5 3.3 1.0 Imposed Load (kN/m2) 1.0…

A: Given data:- Unit weight of concrete is 2.35 kN/m3 Below table is given;   Dead load  (kN/m2)…

Q: The sides of a rectangle are 42cm and 59cm. Find its diagonal? *

A: The given question comes under surveying subject of civil engineering, in the given question sides…

Q: Determine 1. Coefficient Uniformity 2. Coefficient of Curvature of the table.

A: Mass retained are noted in laboratory experiment for each sieve. Total mass of soil = 2457…

Q: The flow lines and equipotential lines together are the mesh strands which form the flow net. What…

A: Graphical representation of water flow of from a soil mass is flow net. It is a net in the form of…

Q: Submit 5 problems with solutions involving static determinacy and indeterminacy

A: 1. For the above problem: Total number of reaction r = 3 (Fixed at A) + 2 (Hinge at B) + 1 (Roller…

Q: What is the horizontal distance of the resultant of the 2 forces below from point A? Give the answer…

A:

Q: You can erase mistakes in a field book. True O False

A: Field book in surveying:- A handbook with useful information written for or with the purpose of…

Q: 5. The four-sided, closed figure below has the following interior angles and distances AB Bearing N…

A: Knowing the main points like distances and angles between points and contours helps engineers decide…

Q: Question 8 The difference in elvation is defined as: (Choose the best definition.) O the vertical…

A: Option (1) is the correct answer. The level surface is the surface parallel to the mean surface of…

Q: What is the magnitude of the fifth force F? What is the direction (∅) of the fifth force F?…

A: GIVEN : Diagram is given along with forces. TO FIND: Fifth Force =?

Q: What is the method of measuring or laying out horizontal distances by stretching a calibrated tape…

A: The method  of measuring or laying out horizontal distance by stretching a calibrated tape between…