For the zener diode voltage regulator circuit of Fig.8, sketch the relation between V and I (VL versus IL). Plot the relation between Is and Rp. Sketch also the relation between Iz and I. Comment on the resulting curves. Rs mA 330 0. 2W Iz mA 15V V. BZKSSCSVI 5.1V Zener Figure 8: Practical Circuit for Zener Diode Voltage Regulator with Variable Load Resistor

For the zener diode voltage regulator circuit of Fig.8, sketch the relation between V and I (VL versus IL). Plot the relation between Is and Rp. Sketch also the relation between Iz and I. Comment on the resulting curves. Rs mA 330 0. 2W Iz mA 15V V. BZKSSCSVI 5.1V Zener Figure 8: Practical Circuit for Zener Diode Voltage Regulator with Variable Load Resistor

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Please answer in short I will like but please asap please urgent... Consider the circuit shown in the figure. Assume that each diode has a turn-on voltage of V_gamma = 0.6V. a) Determine R1, R2 and R3 such that, ID1 = 0.2mA, ID2 = 0.3mA and ID3 = 0.5mA. b) Find the voltage across V1, V2 and the current for each of the diodes for, R1 = 10kΩ, R2 = 4kΩ and R3 = 2.2kΩ.
8. Determine the output voltage V, and the Zener diode current Iz for the circuit below. The Zener diode is IN5236B. }} a) E-21 V, R1=1 km2, and R2-2 km2 b) E-21 V, R1-2 k2, and R2-1 k E R₁ www R₂
Load-line Analysis a.1 For the series diode configuration employing the diode characteristics given, determine: Vp, ID, Voa, Ioa, VR. Draw the load-line and plot the Q-point. Using the Q-point values, calculate the dc resistance Rp. A Io (mA) 20 18 VD 16 + 14 Si 12+ 10+ 8 E 10 V 0.5 k2 VR R 4 2 -- 0. 0.5 0.8 Vp (V) (a) (b) a.2 Repeat a.1 using the approximate model of a silicon diode. Note: You will use the characteristic curve of the approximate model of a diode and plot the same load-line.
1. Describe what will happen to the output voltage and PIV of a center-tapped full wave reciiier n we" consider the diode voltage in the computation. 2. Sketch ir and vo for the network below for the input shown.
In RL load connected (without free transition diode), single phase, uncontrolled, full wave rectifier (4 diodes), the source voltage is sinusoidal and its effective value is 44Volt, 50 Hz. The ohmic load value connected to the circuit is 10 ohms. Average value of load current calculate. (L>>R) a) 4.16 A b) 3.46 A C) 3.26A d) 4.56 A e) 3.96 A
5) The figure below illustrates a simple voltage threshold detection circuit. To understand how it operates, we will analyze its behavior based on the simple constant voltage drop model for both diodes. Assume the Zener diode (Z1) only conducts when its breakdown voltage of 10V is reached. Di is a red light emitting diode (LED). Assume it conducts after its forward bias voltage of 1.8V is reached. Vin is unknown. Assume Zj acts as a perfect Zener diode (without series resistance). What voltage does Vin have to reach before there is a current through R¡? What voltage must Vin reach before current flows through R2? Write an equation for the current through Zi in terms of Vin, Rị and R2 that is valid when Vin is high enough for both diodes to be conducting. a. b. c. R2 Vino R1 LED
Homework Help
a) Find the value of DC voltage of the RL load resistance.b) Find the required rated PIV values for each diodes.c) Find the maximum conduction current of the diodes.d) Plot waveforms of the output current and voltage values.
A commercially available IN4002 diode used in power supplies has the following typical data: (VDI, IDI) = (0.6V, 1mA) (VD2, ID2) = (0.8V, 100mA) Find its reverse saturation current Is and ideality factor n.
What is meant by the PIV rating of a diode?a) Maximum reverse bias potential which can be applied across a diode without breakdownb) Maximum forward bias potential which can be applied across a diode without breakdownc) Minimum potential required by a diode to reach conduction stated) Maximum power allowable to a diode
Subject : Electronics Engineering
6) We can say about the zener diode:a) The Zener diode works in the breakdown region, that is, it works with reverse bias.b) The Zener diode must be connected in series with a current limiting resistor for the Zener, Rs.c) The use of the Zener diode and its current limiting resistor must be placed in parallel with the load.d) The Zener diode and its current limiting resistor should not be considered as a type of voltage regulator.e) None of the above statements are correct.