For the wall shown in the figure: A) Calculate the distribution of pressures according to Rankine, assuming an active state. B) Calculate the Thrust and its point of application. = 2.0 ton/m2 ↓↓↓ ↓↓↓↓↓ Y = 1.60 ton/m3 NAF H1 = 2.0 m ARENA Y = 0.60 ton/m3 C = 0 ton/m2 = 33° H2 = 8.0 m

For the wall shown in the figure: A) Calculate the distribution of pressures according to Rankine, assuming an active state. B) Calculate the Thrust and its point of application. = 2.0 ton/m2 ↓↓↓ ↓↓↓↓↓ Y = 1.60 ton/m3 NAF H1 = 2.0 m ARENA Y = 0.60 ton/m3 C = 0 ton/m2 = 33° H2 = 8.0 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2.5. Water is flowing in a horizontal 200-mm diameter pipe at a rate of 0.06 m³/s, and the pressures at sections 100 m apart are equal to 500 kPa at the upstream section and 400 kPa at the downstream section. Estimate the aver- age shear stress on the pipe and the friction factor, f.
The diameter of a tall stand pipe with an open top is 1.8 m, and the wall thickness is 15 mm. 1. At what water level will the stand pipe's wall experience a 10 MPa circumferential stress? 2. How much axial stress is there in the tank's wall owing to water pressure? 3. If the tank is exposed to a 600 kN lateral force at the top. Determine the tank's shearing stress.
A plate moves 10 cm/s to the right is 0.6 cm above a stagnant wall. The fluid bet. the plate and the wall has a viscosity of 1.8 cP. Compute the shear rate.
For linear stress variation over the base of the dam of the figure, find where the resultant crosses the base and compute the maximum and minimum pressure intensity at the base. Neglect hydrostatic uplift. Ans.Pmax=555 kPa; Pmin=129 kPa Note: unit weight of concrete is 2.5 times unit weight of water. 6m 19m 1 Y'=2.5Y 1 30 40 ¹3 mi 4 m -11 m
The pressure drop in a 15 cm dia horizontal pipe is 100 kPa in a distance of 10 m. Then find the shear stress in the pipe wall in kPa.
The center of a rectangular area at the ground surface has Cartesian coordinates (0, 0), and one corner has coordinates (7, 18). All dimensions are in meters. The area carries a uniform pressure of 135 kPa. Estimate the stresses at a depth of 15 meters below the ground surface at each of the following locations: (0, 0), (0, 18), (7, 0), (7, 18), and (12, 28).a. Obtain the values by the Boussinesq methodb. Compare the results with those of the 2:1 methodc. Comment on the resultsHint: In the Boussinesq method, the equations attached can be used.
A cylindrical tank with closed ends contains compressed air at 850 kPa. The inside diameter of the tank is 1.2 m, and the wall thickness is 0.01 m (that is, 10 mm). Calculate the longitudinal and circumfrential stresses in the tank walls.
Stress=100MN/m Area=bh b=0.5m h=? Determine the stress in members BC, CD and CE A= bh
9.3 What must be the wall thickness of a thin spherical vessel of diameter 1 m if it is to withstand an internal pressure of 70 bar (7 MN/m2) and the hoop stresses are limited to 270 MN/m²? [12.96 mm]
Q-The flow of water (mass density - 1000 kg/m³) and kinematic viscosity = 106 m² /sec, a compressible pipe with equivalent roughness Ks as 0.12mm yields average shear stress at the pipe boundary = 600N/m². The value of Ks/8' (8' being the thickness of laminar sublayer) for this pipe is ...
H H₂ H (b) c. Determine the reaction at Strut A (in lb). d. Determine the reaction at Strut B (in lb). e. Determine the reaction at Strut C (in lb). f. Determine the reaction at Strut D (in lb). Clay 7₁. CL Clay Y2- €₂ Clay f Yn C Refer to the figure above which shows a braced cut in layered clay. Given: H = = 25ft H₁ = 5ft H₂ = 10ft C₁ = 2125psf C₂ = 1565psf 1/₁ = 111pcf Y2 = 107pcf H3 = 10ft C3 = 1670psf Y3 = 109pcf a. Determine the average cohesion (in psf) for the construction of the earth-pressure envelope. b. Determine the average unit weight (in pcf) for the construction of the earth-pressure envelope. If the strut A, B, C and D is located at a depth of 5ft, 10ft, 15ft and 20ft, respectively. The center-to- center strut spacing in the plan = 12ft.
Assignment -2: If the pressures at pipes 1 and 4 are 30 kPa and 120 kPa respectively, determine the length AB. Oil, S = 0.9 Hg 0.6