For the vertical wall shown on the left, the oil thickness is assumed to be 0.2 m and its SG is 0.8. Assume the wall and gate width (into the paper) are 2 meters. Draw the pressure diagram. Assume the density of water is 1000 kg/m2 and g = 9.8 m/s2. Oil Determine а. Pressure at the interface between oil and water Water b. Pressure on the hinge С. Pressure at the base of the gate 2.1 m d. Amount of force acting on the gate Hinge е. Location of the force relative from the hinge 2-m-wide 0.8 m gate

For the vertical wall shown on the left, the oil thickness is assumed to be 0.2 m and its SG is 0.8. Assume the wall and gate width (into the paper) are 2 meters. Draw the pressure diagram. Assume the density of water is 1000 kg/m2 and g = 9.8 m/s2. Oil Determine а. Pressure at the interface between oil and water Water b. Pressure on the hinge С. Pressure at the base of the gate 2.1 m d. Amount of force acting on the gate Hinge е. Location of the force relative from the hinge 2-m-wide 0.8 m gate

Name: For the vertical wall shown on the left, the oil thickness isassumed
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: For the vertical wall shown on the left, the oil thickness isassumed to be 0.2 m and its SG is 0.8. Assume the wall and gatewidth (into the paper) are 2 meters. Draw the pressure diagram.Assume the density of water is 1000 kg/m2 and g = 9.8 m/s2.Oil

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The U-tube manometer is filled by several fluids as shown. Compute the pressure reading at the…

Q: A multifluid container is connected to a U-tube, as shown in the figure. For the given specific…

Q: image, a pressure change of 35 kPa in pressure of air occurs. Here the brine-mercury interface in…

Q: Problem 2 Two open water tanks are connected through a manometer as shown in the figure below. (a)…

Q: The device shown is the buoyancy measurement device used to measure the liquid height change. A…

A: GivenForce measured by the force sensor, Fsensor=7.53 NDistance of force sensor from the pivot,…

Q: Oil h a m bm Water B

A: The pressure gradient along vertical direction in a hydrostatic system depends on density and…

Q: U - tube is used to pressure the difference in water channel. p1= 1000 kg/m3. The orange fluid in…

A: Given:p1=1000 Kg/m3P2=2000 Kg/m3a=10 cmh=15 cmP1=111 KPa

Q: Oil specific gravity of oil = 0.80 1 ft 4 ft Water

Q: 3. Consider a 0.15 mm diameter air bubble in a liquid. Determine the pressure difference between the…

A: Given Diameter of bubble = 0.15 mm It is asked to find excess pressure in bubble for surface…

Q: For the vertical wall shown on the left, the oil thickness is assumed to be 0.2 m and its SG is 0.8.…

A: (a) To draw: The pressure diagram. Given: The density of water 1000 kgm2. Thickness of oil is 0.2 m.…

Q: Water fills the pipe AB such that the absolute pressure at A is 450 kPa. The inner diameter of the…

A: FREE BODY DIAGRAM is a diagram of the system which represents all the forces acting on the system.…

Q: If there are two points A and B. A is located at a distance of h = 5.50 m below you and B is located…

Topic Video

Question

For the vertical wall shown on the left, the oil thickness is
assumed to be 0.2 m and its SG is 0.8. Assume the wall and gate
width (into the paper) are 2 meters. Draw the pressure diagram.
Assume the density of water is 1000 kg/m2 and g = 9.8 m/s2.
Oil
Determine
а.
Pressure at the interface between oil and water
Water
b.
Pressure on the hinge
С.
Pressure at the base of the gate
2.1 m
d.
Amount of force acting on the gate
Hinge
е.
Location of the force relative from the hinge
2-m-wide
0.8 m
gate

Expert Solution

Step 1

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

1) Determine the Air Pressure at Point A when the other end of the manometer at Point B is open to the atmosphere. 2) If passages at Point B is suddenly closed at 1.5 meters above the mercury surface while the Air Pressure at Point A have already been determined earlier, calculate for the Pressure of Air trapped at Point B. Oil, s=0.87 A Patm Air Br 1.2 m 1.4m Water 1.6 m Mercury
If the wall in following figure is 4 m long, calculate the total force on the wall due to the oil pressure. Also determine the location of the center of pressure and show the resultant force on the wall.
A 10cm x 10 cm x 10cm block of steel (ρsteel = 7900 kg/m3) is suspended from a spring scale. The scale is in Newtons. a. What is the scale reading if the block is in air? b. What is the scale reading after the block has been lowered into a beaker of water and is completely submerged?
can u solve pls #3
(Just Question a.) A water filled pipe has water flowing at v1= 5.90 m/s in a section of pipe where the diameter is d1= 20.2 cm and the pressure is known to be P1= 7.00×104 N/m2 above atmospheric pressure. If the pipe carries the water 3.5 meters up hill without any change in diameter, what is the new absolute pressure within the pipe? After flowing up the hill described above, the pipe narrows to 80% of its original radius, what will be the new water velocity (v2) in the pipe? What will be the absolute pressure (P3) in the smaller pipe? a. What is the volume flow rate through the smaller pipe?
In flat areas, water towers are used to supply water to houses. Water is pumped into the tower, and then directed from the tower to houses so that when people turn the water on there is water pressure. The top of the tower is vented to the atmosphere. (a) What is the gauge pressure (total pressure minus atmospheric pressure) at each of the two houses? (in Bernoulli's equation, if the water is not running, you can set v = 0 on both sides, and the external pressure in the water tower is just atmospheric pressure). (b) If a faucet is circular with diameter of 2.0 cm, what is the velocity of the water in each house? You can assume that the velocity of water within the tower is negligible. Vent- B. 15.0 m Faucet 7.30 m Faucet-
A 10000 litre water tank is placed on a building roof and filled to capacity. The empty tank has a mass of 550kg. It is supported on 4 feet, each of which is a 300 x 300 mm steel plate. What is the pressure exerted by each plate, in Pa? (Round your answer to 2 significant figures)
Find the force of oil on the top surface CD of the figure below if the liquid level in the open pipe is reduced by 4.0 ft.
Consider the pressure and force acting on the pool retaining a reservoir of water. Suppose the pool is 50m wide and the water is 8m deep, as illustrated below. (a) What is the Gauge pressure on the dam due to the water? (b) What is the absolute pressure at10m depth of the dam? (C) Calculate the force exerted against the dam. Density of water is 1000kg/m3.
The device shown is the buoyancy measurement device used to measure the liquid height change. A pressure sensor is installed at the bottom of the tank, and a force sensor is installed to measure the upward force on the horizontal lever. The distances to the pivot point from the force sensor and cylinder are X1 and X2, respectively. The reference pressure at the reference liquid height, h0, to the bottom of the cylinder is pref. (4) If the force measured by the force sensor is Fsensor = 7.53 N, X1 = 1.58 m, X2 = 0.17 m, the diameter of the cylinder is D = 0.05 m, and the specific weight of the liquid is γf = 8.70 kN/m3, calculate the liquid height difference, Δh, relative to the reference height h0. __________ m.