for the utility in problem 8-3, will the utility pole be located too close to the road if it is on the outside of a horizontal curve with a radius of 2,000 f? 8-3 A road with a design speed of 55 mph has a utility pole located 27 ft from the edge oftravel lane. If the ADT for the road is 1,850 vpd and the sideslope slopes down at a 1V:4Hgrade, is the utility pole located within the clear zone?8-4 For the utility in Problem 8-3, will the utility pole be located too close to the road if itis on the outside of a horizontal curve with a radius of 2,000 ft?

The “clear zone” distance is a component in collision reduction and refers to the distance allowed…

Answered: for the utility in problem 8-3, will…

for the utility in problem 8-3, will the utility pole be located too close to the road if it is on the outside of a horizontal curve with a radius of 2,000 f?

Traffic and Highway Engineering

5th Edition

ISBN:9781305156241

Author:Garber, Nicholas J.

Publisher:Garber, Nicholas J.

Chapter7: Intersection Design

Section: Chapter Questions

Problem 19P

See similar textbooks

Related questions

Q: 12. The stopping sight distance of a vehicle is 295 meters. Given that the acceleration of the…

A: solution as per the guideliness consider total perception and reaction time =2.5secAAHTOacceleration…

Q: The crossing of traffic streams moving the same general direction accomplished by merging and…

A: Given data in question Traffic streams Merging and diverging To find out Accomplished merging and…

Q: If the curve lead of a BG turnout is 16.76m, the angle of crossing of the turnout will be given by…

Q: What is the intersection sight distance (ft) needed at a yield controlled intersection for a…

A: Given, Design speed of car= 50mph Left Turns with Yield Controlled intersection Find out :- ISD

Q: In the 4- legged intersection, if G1=11.31 sec, G2 1.2 min., G3 = 58 sec, N1= 100, N2 = 560…

A: Data Given: G1 = 11.31 sec.G2 = 1.2 min. = (1.2 × 60) = 72b sec.G3 = 58 Sec.N1 = 100N2 = 560…

Q: A large grain elevator is located 40 feet from the centerline of a two-lane highway (55 mph…

A: Step 1:Step 2:

Q: Calculate the minimum length of overtaking zone of a one way traffic road if the velocity of the…

Q: A large grain elevator is located 40 feet from the centerline of a two-lane highway (55 mph speed…

Q: A horizontal curve with a radius of 240 m connects the tangents of a two-lane highway that has a…

Q: Two adjacent signalized intersections along a major arterial are 650 ft apart (stop line to stop…

A: Transportation engineering : Transportation engineering is a discipline of civil engineering…

Q: Q6. Given horizontal curve has two-lanes with lower-than-average coefficient of side friction (0.1)…

A: The given data is as follows:

Q: Write down the general solution of the associated system of linear equations. (Assume x = traffic…

Q: 3. An engineering mistake has resulted in the need to connect an already constructed tunnel and…

A: St of tunnel floor = 0+00 St of bridge deck= 4+00 Elevation of tunnel floor= 100feet Elevation of…

Q: Maximum permissible speed on a railway track (BG track) is 100 kmph. calculate radius of the curve…

A: Given data in question Broad guage Speed To find out Radius of curve Degree of curve

Q: Q- Highway geometric design & planning. The design speed is 100 kmph, perception reaction time is 3…

A: Given data- Design speed V=100 kmph, Reaction time t=3 s, Coefficient of friction f=0.25, To Find-…

Q: What is the intersection sight distance (m) needed at a stop controlled intersection for a passenger…

Q: A 6 lane highway (3 lanes in each direction) has 11 ft wide lanes, 8 ft wide shoulders, 50 degree…

A: Given, Design speed = 60 mph Central deflection = 65o

Q: 4. A car is traveling downhill on a suburban road with a grade of 4% at a speed of 35 mph. Determine…

A: stopping sight distance (SSD) One sort of sight distance utilized in road design is stopping sight…

Q: SAMPLE PROBLEM Design the intersection given the following vehicular volumes per leg in pcu. Assume…

A: Given Data: Vehicle volumes are given in terms of PCU (Passenger Car Unit) Saturation flow rate is…

Q: For the through movement of the north-bound approach, what is the minimum change and clearance…

A: Given; Travel speed = 45 mph A geometric layout with a +3% upgrade = +0.03 And a semi truck with a…

Q: Calculate the end area for the following stations with 30-ft wide roadway and 4:1 slop:…

Q: For the STOP-controlled intersection show below, is the sight distance sufficient for safe…

A: Given :- a STOP controlled intersection Reaction time = 2.5 s Lame width of EW street = 12 ft

Q: Briefly describe highway developmentThe speed of overtaking vehicle is 90 kmph and acceleration is 3…

Q: A vertical curve connects a +3% grade with a -2.0% grade on a rural highway at station 13+94.00 and…

Q: What is the intersection sight distance (ft) needed at a yield controlled intersection for a…

A: Given :- Passenger car Design speed , V = 50 miles per hour 2 way 2 lane road To Determine :- The…

Q: what could happen if this section of road way provided a sight distance of (500)ft V=(70)mph , if…

Q: The radius of a horizontal curve on an existing highway was field-measured to be 243 m. The pavement…

A: Given Posted speed limit= 96km/h

Q: What is the calculated stopping sight distance (ft) for a -3% grade when the design speed is 55 mph,…

Q: What deceleration rate (ft/s2) does AASHTO recommend for calculating stopping sight distance?

A: Stopping sight distance is the minimum distance required to stop a vehicle without collision when…

Q: What is the intersection sight distance (ft) needed at a yield controlled intersection for a…

A: The 2-way 2-lane road is given Design speed = 50 mile/hr To determine the intersection sight…

Q: A turnout has an angle of 22 degrees. Determine its frog number.

Q: What is the intersection sight distance (ft) needed at a yield controlled intersection for a…

A: Given: design speed(v)=50mph 2-way 2-lane road. Unit used: 1m=3.28084ft 1kmph=518m/s

Q: Find minimum sight distance to avoid head-on collision of two cars approaching at 90 kmph and 60…

A: given data V1= 90 Km/h V2= 60 Km/h t = 2.5 sec f = 0.7stopping sight distance of first car with…

Q: Determine the grades of a symmetric VC that requires a stopping sight distance of 434.3 ft and…

A: Vertical curves are provided where there is a change of gradient along the length of the road.…

Q: Question 2 highway. The inside lane is 3 m wide and the edge of the road shoulder is 2 m from the…

A: HSO = R1-Cos28.65SR where R - radius of curve S - stopping sight distance Design speed…

Question

for the utility in problem 8-3, will the utility pole be located too close to the road if it is on the outside of a horizontal curve with a radius of 2,000 f?

8-3 A road with a design speed of 55 mph has a utility pole located 27 ft from the edge of
travel lane. If the ADT for the road is 1,850 vpd and the sideslope slopes down at a 1V:4H
grade, is the utility pole located within the clear zone?
8-4 For the utility in Problem 8-3, will the utility pole be located too close to the road if it
is on the outside of a horizontal curve with a radius of 2,000 ft?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Ninth Lecture Civil Dept. Example 15.8 Location of Object Near a Horizontal Curve A horizontal curve with a radius of 240 m connects the tangents of a two-lane highway that has a posted speed limit of 56 kmph. If the highway curve is not super- elevated, e = board can be placed from the centerline of the inside lane of the curve, without reducing the required SSD. Perception-reaction time is 2.5 s, and f 0.35. 0, determine the horizontal sightline offset (HS0) that a large bill-
Please i need solve on 10 minute
What is the intersection sight distance (m) needed at a stop controlled intersection for a passenger car to turn left onto a 2-way, 2-lane road with a design speed of 90 km/h? [round to the nearest meter] Response Feedback: ISD=0.278V t major g
3-19 The radius of a horizontal curve on an existing highway was field-measured to be 243 m. The pavement on this two-lane highway is 6.6 m wide, and the elevation difference between the inside and outside of the curve is 0.43 m. The posted speed limit on the road is 96 km/h. Is this a hazardous location? If so, why? What action will you recommend to correct the situation?
10-25. In preparation for a public hearing on a proposed interstate bypass at Non- troppo, Michigan (Figure P-10-25a), the County Road Commission has re- quested that you prepare an estimate of the potential for violation of FHA noise standards 75 m from the interstate. The city engineer has supplied sketch maps (see Figure P-10-25b) and data summary for your use. Data for 1-481 at Pianissimo Avenue Estimated traffic: Automobiles: 7,800 per hour at 88.5 km/h Medium trucks: 520 per hour at 80.5 km/h Heavy trucks: 650 per hour at 80.5 km/h Roadway configuration: Depressed Section length: 857.25 m east and 857.25 m west of center line of Pianissimo Avenue Assume that the receiver is located on the center line of Pianissimo Avenue 75.00 m from the center line of 1-481. Answer: L₁ at observer = 68.6, or 69, dBA
Find minimum sight distance to avoid head-on collision of two cars approaching at 90 kmph and 60kmph. Given t=2.5sec, f=0.7.
A vehicle moving in wet weather along down grade highway of (- 4%) grade. The design speed (48mile/hr.), (f = 0.30), (t = 2.50 Sec.). The stopping sight distance you %3D %3D recommended is equal to:
plz, solve this problem, it is not graded question. Transportation Engineering-1 During a 70 sec period, a detector is occupied by vehicles for the following times: 0.31, 0.39, 0.41, 0.35, and 0.53 sec. Estimate the values of flow (q), density (k) and speed (v). Assume that the loop detector is 10 ft and that that the average length of the vehicle is 20 ft.
A 6 lane highway (3 lanes in each direction) has 11 ft wide lanes, 8 ft wide shoulders, 50 degree central angle (As), 65 degree central angle (A), design speed of 60 mph and a Pl station at 42+50. What are the PC and PT stations?
DATA COLLECTION AND REDUCTION METHODOLOGIES 60° angle from a perpendicular line from the observe location to the entry boundary-If one of the observed travel times to traverse the trap is 8.3 seconds, at wha speed is the vehicle traveling? 4. Briefly desrrit now wuing L..- -. .vul stuu, speed study was conducted using manual observa- tion with stopwatches. The trap length was marked for 400 feet. The observer lined up with the entry boundary line, 60 feet away from the vehicles being observed. When viewing the exit boundary, the sight line was at a 3. of nermanent detectors avail- d...
i need the answer quickly
QUESTION 1 What deceleration rate (ft/s²) does AASHTO recommend for calculating stopping sight distance?