For the unbalanced circuit in Fig. 12.25, find: (a) the line currents, (b) the total complex power absorbed by the load, and (c) the total complex power absorbed by the source. a 120/0° rms п 120/120° rms C Figure 12.25 For Example 12.10. A j5Q N 120-120° rms -j10 102 b B C

Q: Question 2 : al khat are the differences between logical and Continuous Sensors. b) Name two logical…

A: a) The main differences between logical and continuous sensors lie in the type of data they provide…

Q: A machine producing components with a 10% defective rate. Determine in a sample of 6 components…

A: Percentage of defective items = 10% Sample size = 6 Probability of defective components = 4

Q: a- Draw the circuit of 4-bits Johnson counter and draw its timing diagram

A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…

Q: he system with a velocity constant can have the error removed by adding Select one: a. PD-controller…

A: By adding one pole in the system with a velocity constant  Integral controller remove error of the…

Q: 14. A system gives an output 15. A system has a transfer function of 5/(s+3). What will be its…

A: 15.) It is given that: Hs=5s+3

Q: What is FSM?

A: FSM stands for finite state machine which is used for the simulation of the sequential logic or it…

Q: For a horizontal sieving machine project, I want to know the minimum input power of the DC motor if…

A: This question is from the "Electrical machine". Under which we are going to study about the loading…

Q: Q2/A-list the characteristics of PIC 17 series B- Explain with drawing the basic blocks in PIC16F48

A: (A) PIC 17   a memory mapped accumulator. read access to code memory (table reads) direct register…

Q: PID LOOP SIMULATOR M 00 3.4 Kp + + Kps 10r +1 Reference RPMI Controller DC Motor Controller Kp KI KD

A: The response of a dynamic system towards inputs expressed as a function of time is called the time…

Q: Q3) What is the purpose of Placement step in Digital IC design. Clarify the required inputs to a…

A: Placement step is the important step in which physical design flow and that assign the components of…

Q: With an elegant drawing, explain the characteristics of the dynamic operation of the device used in…

A: To explain the characteristics of the dynamic operation of the device

Q: What is meant by Paging? Give its advantages

A: Paging: Paging is nothing but a memory management technique that can reduce the need for physical…

Q: a. The time it takes for the step response to rise to 63% of its final value. b. The time it takes…

A:

Q: Please indicate if the following system is controllable 1 - 1.5 JLX2.

A: For controllable rank (B:AB) should be equal to n ,Here n is 2.

Q: How many select lines are required for a 1-to-8 demultiplexer? Select one: a. 4 b. 3 Cc. 2 d. 5

A: Given data, Select lines requires in 1-to-8 demultiplexer.

Q: xplain the block diagram of a Displacement measurement system . Also identify the names of the…

A: Diagram of displacement measurement system: The system has a single primary winding P and two…

Q: justify balance modulators are used as mixers

A: The balanced  modulator or a mixer uses the  four-port hybrid junction that is shown below. The LO…

Q: wave analyser is basically a superheterodyne receiver covering the following range of frequency with…

A:

Q: What is the order of precedence in ?python

A:

Q: Explain the Difference between Two position controller and Pl controller?

A:

Q: The benefits of writing program in assembly: It is essay to write and modify Machine code program…

A: The explanation of advantages of assembly language are as follows.

Q: 7.what do you mean by instruction cycle,mechine cycle and T- state

A: Instruction cycle: The time taken by the processor to  fetch and execute an instruction is called…

Q: similarity of fraction formula and Euclidean algorithm

A: Fraction Formula:A fraction represents a numerical price, that defines the components of a…

Q: A type of noise that is directly proportional to the frequency of the operation. a. shot noise b.…

A: Another quite noise that happens in transistors is referred to as transit time noise. Transit time…

Q: AIWhat is the difference between clippers and clampers ? sketch the * .circuit

A:

Q: 1_ What do you consider to be the main difference between a hydraulic actuator and a hydraulic…

A: Hydraulic pressure sensors give good repeatability and precise findings over long periods of time.…

Q: Explain briefly construction of D.C. machine and What are the functions of a Yoke in DC mạchines?…

A: Construction The DC machine consists of parts like, yoke, poles, armature, armature winding, pole…

Q: Please answer in typing in short

A: SOLUTION:b) Providing fast response time (Correct Answer): Proportional control improves the…

Q: What are electronic sensors? Who is composed?

A: Electronic sensors are the devices that are used to detect the physical quantities in any physical…

Q: A software company lost many of its clients because they were not able to update to latest and new…

A: They lost the clients because other companies were offering better technologies. This is called lack…

Q: Choose how many and determine the type of output (digital or analog) it gives and how to interface…

A: 16 channels on the ESP32 can be utilized to generate PWM signals, allowing for a maximum of 16…

Q: is measures the wind speed and transmits wind speed data to the controller.

A: Answer is  Anemometer Anemometer is a measuring device which measures the wind speed. It will…

Q: Introduction explaining the importance of the measurement process

A: Importance of measurement process in electrical  and electronics systems is shown below using…

Q: is a term used to describe complete combustion to ashes. Fluidized bed combustion O Gasification O…

A: ___________ is a term used to describe complete combustion of ashes a) fluidized bed combustion b)…

Q: f) Briefly describe the significance of multi-sensor integration in the following applications and…

A: The multi sensor has many sensors, including a vibration sensor, and is meant to identify wear…

Q: The you measure the clock signal for the ATMegaXYZ migrocontro ller and the following: the clock is…

A: Given   Clock high pulse duration :Ton :100 nsec Clock low pulse duration : Toff : 25 nsec

Q: 1. Draw the internal design of a microcontroller and explain each block diagram. 2. What are the…

A:

Q: Select the best answer for the question. 4. Look at the drawing shown in the figure above. When you…

A: Here is a simple description of each option: A. Step-up transformer: This device increases the…

Q: How far are the CT Scan machines related to electrical engineering?

A:

Q: Draw the block diagram representation of linear ramp type digital voltmeter and name the blocks.

A: Answer for the questionis