For the truss shown below, the area of all bars is 1.8 in?; E is 30,000 kips/in? 1) determined the static determinacy of the truss 2) determine the vertical deflection at C if the truss is ONLY subjected to the force at B 2) determine the vertical deflection at C if the truss is ONLY subjected to the force P at C 3) when the truss is subjected to both forces at B and C, determine the value of the force P if the vertical deflection at C is to be zero

Q: On the drawing (attached , apply a datum feature symbols to create a datum axis A-B by using the…

A: The given data is: For left side: Shaft Diameter Upper Limit=9 6.40 mmShaft Diameter Lower Limit=ϕ…

Q: Draw the figure of level and show its parts on it.

A:

Q: B 7m |C A 5m 6m 8m

A: Given: A tank filled with lubricant oil exerting 150 kPa Required: To find vertical stress increase…

Q: 不 k H, k2 H3 k3 NOTE: ト -ごー*

A:

Q: 1-2in. -1in-+1int Hin 3in- T 3in 2in

A:

Q: Determine the coordinates of the centroid for the shaded area

A:

Q: & Find the set of solutions xy dx + (y-3x²) dy = 0. %3D

A:

Q: determine the distances x and y for equilibrium if f1=800 N and f2=1000N. (Hand written and clean…

A: Given data - F1 = 800 NF2 = 1000 N Find out - Distance x and y ?

Q: Now please solve 7-10

A: Some statements regarding highway and traffic engineering

Q: Given the multiview projection of the solid, draw its isometric view.

A: Solution- The given diagram is shown below. To Determine,  The isometric view

Q: y 200 mm 300 mm → 125 mm 125 mm 60 mm 150 mm

A:

Q: at state of given (All in The Stres point is MPa) 80 100 100 i) And Principal Stren & Principal…

A:

Q: 1" 5" 2" 1-Determine the location of the centroid (x,y) of the centroid. 2- Determine the Ix0 and…

A:

Q: 16. From a triangular steel plate XYZ, a triangular section VWZ was cleanly cut off. What should be…

A:

Q: A C L- (2) B "1-12- -L/2→ C x

A:

Q: -20 -0.5a 2a/3 T=0.5a

A:

Q: Find the Xp ¢ YT Зст I}1:25 cm Cocn 61.5 cm 0.75 cm

A:

Q: Find the length of side TS.

A: Consider the figure,

Q: 4 in 2 in 4 in 8 in -12 in- -16 in-

A:

Q: Problem 3: A bracket of negligible weight shown in the figure below is loaded a force of 13.34 kN.…

A:

Q: 80 mm -L- В D 60 mm

A:

Q: ex (x+1)² +c

A: Write all numerators above the common denominatorUse  to expand the expression.

Q: 0 mm Infront of VP and 30 m rojection of the line.

A:

Q: 4x-2x2+1 find lim, 3x-5

A:

Q: The moment diagram by parts are base on the moment diagram of O Fully restrained beam O Cantilever…

A: Moment diagrams by parts is a method to solve the determinate beam and find reactions in beam.

Q: Subtract 8.46 from 25.3.   25.3- 8.46

A: Subtract 8.46 from 25.3.

Q: Find the centroid 20 30 25

A: A1=12×20×25=250 square unitA2=30×25=750 square unitA3=π×1522=353.43 square unit

Q: D O00 15KN 15KN B.

A: Given data : Number of member (m)=13Number of external support reaction (R)=2+1=3Number of joint…

Q: Identify the centroid of the 1/4 circle projected whose radius is r. Utilize integration. Yo -x Хо

A:

Q: b (x+c)(x-c) A

A: To solve the expression (x+c)(x-c) step by step, we'll use the difference of squares…

Q: RI 038 R32 80

A: For the given figure, i had drawned in AUTO-CAD using the following commands 1. CIRCLE COMMAND 2.…

Q: For the truss shown, determine the stress in members DC and DG. The area of each member is 800 sq.…

A: Given data: Area of each member is 800 mm2.

Q: 5 \frac{4}{5}-2 \frac{1}{5}

A: Tofind:- difference

Types of Composite

Composite materials are formed by merging two components that have different chemical and physical properties. The merged output is termed as a composite, whose properties are completely different from the individual components. Composite materials also have better strength than the individual components.Composite materials usually have two main parts, reinforcement material, and matrix material. The matrix material acts as a binder and surrounds the fiber of another material that bears a much higher strength. This material is known as the reinforcement material. The matrix materials are usually high-strength additives resins, while the fibers of the reinforced material can be random, oriented, and in a mat format.Composite materials are also known as fiber-reinforced composite polymers because they are composed of the polymer matrix which is reinforced to laboratory-created fibers or naturally occurring fibers, such as glass fibers, carbon fibers, or aramid fibers. Under the application of external loads, the matrix material absorbs and transfers the loads to the fibers, these fibers in return provide good compressive strength, tensile strength, and stiffness to the fiber-reinforced composite materials.Depending upon the matrix and the reinforcement material, different properties can be induced to the fiber-reinforced composite materials, including good corrosion resistance properties. The most common matrix material is the resin while the glass fibers act as the reinforcement material. Strong fibers provide strength and stiffness to the composite materials while, a soft and flexible resin provides shape to the composite materials.